SONIX SN32F280 Series User Manual Download Page 152

Page: 152 / 268

SN32F280 Series

32-Bit Cortex-M0 Micro-Controller

SONiX TECHNOLOGY CO., LTD

Page 152

Version 1.1

12.5 RTC REGISTERS

Base Address: 0x4001 2000

12.5.1 RTC Control register (RTC_CTRL)

Address offset: 0x00



Note: RTCEN bit shall be set at last!

Bit

Name

Description

Attribute

Reset

31:1

Reserved

RTCEN

RTC enable bit
0: Disable
1: Enable. Reset SEC_CNT.

R/W

12.5.2 RTC Clock Source Select register (RTC_CLKS)

Address offset: 0x04



Note: SW shall disable RTC (RTCEN=0) when changing the value of this register.

Bit

Name

Description

Attribute

Reset

31:1

Reserved

CLKSEL

RTC clock source selection.
HW will reset SEC_CNT and ALM_CNT when changing the value.
0: ILRC
1: ELS X’TAL

R/W

12.5.3 RTC Interrupt Enable register (RTC_IE)

Address offset: 0x08

Bit

Name

Description

Attribute

Reset

31:1

Reserved

SECIE

Second interrupt enable
0: Disable
1: Enable

R/W

12.5.4 RTC Raw Interrupt Status register (RTC_RIS)

Address offset: 0x0C

Bit

Name

Description

Attribute

Reset

31:1

Reserved

SECIF

Second interrupt flag
This bit is set by HW when SEC_CNT=SEC_CNTV. An interrupt is
generated if SECIE=1.
0: Second flag condition not met.
1: Second flag condition met.

12.5.5 RTC Interrupt Clear register (RTC_IC)

Address offset: 0x10

Summary of Contents for SN32F280 Series













































































































































































































































































Search results

Summary of Contents for SN32F280 Series

Reviews:

Related manuals for SN32F280 Series

Brands by name

Popular brands

SONIX SN32F280 Series, User Manual

Search results

Summary of Contents for SN32F280 Series

Reviews:

Related manuals for SN32F280 Series

Brands by name

Popular brands