Smiths Medical CADD-Prizm VIP 6100 Manual Download Page 55

Page: 55 / 64

Accessories

Section 5

ces

sories

To attach the power pack or AC adapter

1. Open the cover for the power jack.

2. Line up the red mark on the power pack or

AC adapter connector with the red mark

on the pump. Push the connector in until

it clicks.

NOTE: The connector may or may not be supplied

with the grip shown in this illustration.

3. If using an AC adapter, plug the other end

into a 3-pronged wall outlet.

To detach the power pack or AC adapter

CAUTION:

To avoid damaging the connector or cable, do not use excessive force or

instruments such as pliers to remove the connector from the pump.

1. Grasp the collar on the connector

2. Pull the connector back using a straight, steady motion.

DO NOT twist or turn the connector.

Remote Dose Cord

In the PCA delivery mode, a remote dose cord may be attached to the

pump so the patient can start a demand dose by pressing either the

remote dose cord button or the dose key.

NOTE: The remote dose cord is used only for starting demand doses. It is not

associated with pump communications.

CAUTIONS:

Do not place the remote dose cord where the button might accidentally

be pushed. Accidentally pushing the button may deliver an inadvertent

Demand Dose.

Do not use the remote dose cord to pick up or carry the pump. Using the cord in this

manner could damage the pump or cord.

To avoid damaging the connector or cord, do not use excessive force or

instruments, such as pliers, to remove the remote dose cord from the pump.

Power

Jack

IN19822.indd 49

10/24/2011 3:57:19 PM

Summary of Contents for CADD-Prizm VIP 6100

































































Search results

Summary of Contents for CADD-Prizm VIP 6100

Reviews:

Related manuals for CADD-Prizm VIP 6100

Brands by name

Popular brands

Smiths Medical CADD-Prizm VIP 6100, Manual

Search results

Summary of Contents for CADD-Prizm VIP 6100

Reviews:

Related manuals for CADD-Prizm VIP 6100

Brands by name

Popular brands