Smiths Medical CADD-Prizm VIP 6100 Manual Download Page 30

Page: 30 / 64

Section 2

Pump Programming - TPN Delivery Mode

TPN Cycle Graph and Programming Screens

The TPN delivery mode allows the high volume delivery of

solutions, with optional tapering. Delivery can be gradually

increased or “tapered up” at the beginning of the infusion profi le,

or it can be gradually decreased, or “tapered down” at the end of

the infusion profi le. An automatic Keep Vein Open (KVO) rate is

delivered at the end of the infusion profi le.

The following fi gure shows the programming screens in the

TPN delivery mode:

Reservoir Volume

Infusion Volume

Infusion Period

Taper-Up Period

Taper-Down Period

Rate

(Review)

Milliliters Given

Air Detector

(Review)

*** TPN 6230X ***

STOPPED

Press NEXT to advance

If Air Detector

is installed

Infusion Peroid

Infusion Volume

Taper-Up

Period

Taper-Down

Period

KVO

Infusion Profile

Plateau Rate

(must be at least 10 min.)

IN19822.indd 24

10/24/2011 3:57:14 PM

Summary of Contents for CADD-Prizm VIP 6100

































































Search results

Summary of Contents for CADD-Prizm VIP 6100

Reviews:

Related manuals for CADD-Prizm VIP 6100

Brands by name

Popular brands

Smiths Medical CADD-Prizm VIP 6100, Manual

Search results

Summary of Contents for CADD-Prizm VIP 6100

Reviews:

Related manuals for CADD-Prizm VIP 6100

Brands by name

Popular brands