Smiths Medical CADD-Prizm VIP 6100 Manual Download Page 17

Page: 17 / 64

General Description and Basic Operations

Section 1

Basic Oper

ations

Starting the Pump

When you start the pump, programmed values will be automatically

reviewed. Then fluid delivery will begin as programmed and the

green indicator light will blink. If the pump will not start, a message

will appear on the display. Refer to the Alarms and Messages Table

on page 54.

To start the pump

1. Press

⁄

“Start the Pump?”

will appear.

2. Press

. “Starting Pump”

will appear.

The pump will review the program,

lock level, AutoLock setting,

Air Detector status, time, and date.

If AutoLock is in use, “AutoLock is

changing lock level to (LL1 or LL2)”

will appear.

Stopping the Pump

When the pump is stopped, no delivery occurs. “STOPPED” appears on

the main screen and the amber indicator light blinks.

To stop the pump

1. Press

⁄

If a demand dose or clinician bolus is

in progress, “Stop Demand Dose?” or

“Stop Clinician Bolus?” will

appear. Press

to stop the dose.

2. When “Stop the Pump?” appears,

press

Stop Demand Dose?

Press Y or N

Stop the Pump?

Press Y or N

Start the Pump?

Press Y or N

AutoLock is

changing Lock Level

to LL2

Starting pump...

IN19822.indd 11

10/24/2011 3:57:09 PM

Summary of Contents for CADD-Prizm VIP 6100

































































Search results

Summary of Contents for CADD-Prizm VIP 6100

Reviews:

Related manuals for CADD-Prizm VIP 6100

Brands by name

Popular brands

Smiths Medical CADD-Prizm VIP 6100, Manual

Search results

Summary of Contents for CADD-Prizm VIP 6100

Reviews:

Related manuals for CADD-Prizm VIP 6100

Brands by name

Popular brands