Siemens TX-I/O User Manual Download | Manualshive

Page: 57 / 94

background image

57 / 94

Siemens

TX-I/O PROFINET BIM V1.0

CM110564en_02

Building Technologies

Parameters

23.09.2010

Parameter – type [AnalogValueEnum] – that represents the backup value and
becomes valid in the following cases:



a change in status to 'MasterDown'

and



the parameter [BackupMode] = VALUE

Value range

Unit

0...10000 0.01

%

4.12.4 StartSynchronization

Parameter – type [SynchEnum] – for synchronization after a reset.

The synchronization cannot be interrupted. After a reset the current position of the
stroke model is set to 0 % before the synchronization is started.

Possible values

Description

NONE No

synchronization

SINGLEOPEN

Immediate opening synchronization for 1.5



[rise time]

SINGLECLOSE

Immediate closing synchronization for 1.5



[fall time]

4.12.5 LimitSynchronization

Parameter for stopping a drive at specified end positions. In doing so, [StrkPos] is
set to [AOValue] at the same time.

While [LmStp]=TRUE,



all synchronization types remain irrelevant



any ongoing synchronization operation is cancelled

If the local override function is active, [LmStp] is set to FALSE.

Note

The function becomes even more useful if an end position detection function is
available with an additional input and a correspondingly assigned end switch.

Possible values

Description

Selected No

synchronization

Not selected

Stop

4.12.6 StartSynchronization

Parameter for starting the synchronization.



StartSynchronisation is automatically triggered after a reset if this has been
specified accordingly.



The synchronization is not interrupted by any other event.

Possible values

Description

NONE No

synchronization

SINGLEOPEN

Immediate 'Open' synchronization for 1.5



[rise time]

SINGLECLOSE

Immediate 'Close' synchronization for 1.5



[fall time]

Definition,

addition

Definition,

addition

Definition,

addition

Definition,

addition

«
...
55
56
57
58
59
...
»

Summary of Contents for TX-I/O































































































Reviews:

No comments

Related manuals for TX-I/O

Brand: DAB Pages: 8

Brand: U-Line Pages: 7

Brand: Jensen Pages: 12

Brand: Teac Pages: 2

Brand: AeroAudio Pages: 8

Brand: BendPak Pages: 43

Brand: Perma Pages: 26

Star SuperNova S126

Brand: Tyco Fire Product Pages: 4

Productivity 2000 P2-08NAS

Brand: Automationdirect.com Pages: 4

Brand: Goodmans Pages: 22

Box Design BT Box S2

Brand: Pro-Ject Audio Systems Pages: 6

Brand: Sonos Pages: 15

Enterview MX EVMX2

Brand: ESP Pages: 16

Brand: Bishamon Pages: 19

Brand: Powrmatic Pages: 36

Brand: hager Pages: 73

Brand: Walkera Pages: 22

Brand: Dannmar Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands