Siemens TX-I/O User Manual Download | Manualshive

Page: 14 / 94

background image

14 / 94

Siemens

TX-I/O PROFINET BIM V1.0

CM110564en_02

Building Technologies

Engineering

23.09.2010

3 Engineering

Engineering is based on the GSDML file. It is standardized in accordance with the
GSDML Specification for Profinet IO V2.2.

The engineering tool (Simatic Manager) is part of the engineering process. It needs
to be informed by an import about which GSDML file to use for the Profinet BIM.

As a result of the import, the Profinet BIM will then appear as a field device in the
hardware catalog of the program (path: ...\Profinet IO\I/O\TX-I/O).

Engineering can be carried out in the following two different ways:

1

a) First, the application is created and loaded into the CPU and
b) then the periphery is configured,

or

2

a) First, the modules are configured and tested, and
b) then the application is loaded.

In this case, specific organization blocks (OBs) must be available. If one of

these organization blocks is missing, then in the event of



configuration errors

and



if a

module fails during running operation

the

CPU

will be stopped.

The following organization modules should be available:

OB no

OB name

Meaning

OB82

I/O Point Fault 1

Diagnostics alarm

OB83

I/O Point Fault 2

Removal/insertion (of modules)

OB85

OB Not Loaded Fault

Program operation error

OB86

Loss of Rack Fault

Module rack failure

OB122

Module Access Error

Program operation error

can be found in the online help function of the SIMATIC Manager
If no organization blocks are yet available, you can find information as follows:



SIMATIC Manager

>

Help

>

Find

tab >

Organization blocks

or



SIMATIC Manager

>

Wizard for new project

>

Next

>

Select CPU type

>

Next

> mark the required OB >

Help for OB

button

Note

In this sequence do

not

click the

Finish

button.

We assume in this manual that are beginning a project from the very start. The
following procedure is useful:

1. SIMATIC

Manager

Create a

Step7

project

See Section 3.1 – Create a

Step7

project

2.

Import Profinet BIM GSDML file

Current GSDML file: GSDML-V2.2-Siemens-ProfinetBim-<yyyymmdd>.xml

Refer to Section 3.2 –

Instal GSDML file:

Import GSDML and BMP files

3.

Under HW Config on the programming PC: engineer S7-CPU 2xx/3xx/4xx-
2PN/DP

The corresponding step-by-step method is given below.

GSDML file

SIMATIC Manager

Workflow

Help regarding the
organization blocks
(OBs)

Procedure

«
...
12
13
14
15
16
...
»

Summary of Contents for TX-I/O































































































Reviews:

No comments

Related manuals for TX-I/O

Brand: M-LOCKS Pages: 3

Brand: WALTCO Pages: 20

Brand: fadini Pages: 16

AeGIS 8000 Series

Brand: PACH & COMPANY Pages: 32

AeGIS 7000 Series

Brand: PACH & COMPANY Pages: 2

Brand: MAHA Pages: 23

Feeder/Deliming System EV9797-20

Brand: Everpure Pages: 2

Brand: Rotary Pages: 16

Brand: RTS Pages: 131

DuplicAir Intelligent Control Blue

Brand: Jydepejsen Pages: 52

Brand: S&S Northern Pages: 12

System One M200

Brand: iCentral Pages: 44

Brand: W. A. Production Pages: 5

Brand: C.S.L. Pages: 27

Universal XL HD Lifter

Brand: Garage Smart Pages: 21

Brand: Ravaglioli Pages: 104

UVL Series NUVL604XA

Brand: Braun Corporation Pages: 38

Brand: Global Lift Pages: 51

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands