Siemens TX-I/O User Manual Download

Page: 62 / 94

62 / 94

Siemens

TX-I/O PROFINET BIM V1.0

CM110564en_02

Building Technologies

Diagnostics

23.09.2010

5 Diagnostics

5.1

Diagnostics with the SIMATIC Manager

Identification-related diagnostics are used to diagnose the Profinet BIM.

The function block

DIAG-DESIGO-IO

is provided in the Emx to evaluate the

diagnostics data with the SICLIMAT X environment.

5.1.1

Basic Diagnostics

The following diagnostics information is displayed in the module information window:



the firmware version



the hardware version



MLFB number (machine-readable production number = order number)



Ethernet port statistics

SIMATIC Manager, left screen section:

Mark CPU

> menu:

Target system

Show accessible nodes

Opens the Accessible Nodes dialog box

General tab, group field: Version >

Version

Identification tab, group field: Manufacturer information >

Serial number

4. Statistics

tab

Close

button.

Closes the dialog box.

5.1.2

Advanced Diagnostics

Step-by-step procedure

Version and MLFB
(order number)

Serial number

Ethernet port statistics

Summary of Contents for TX-I/O































































































Search results

Summary of Contents for TX-I/O

Reviews:

Related manuals for TX-I/O

Brands by name

Popular brands

Siemens TX-I/O, User Manual

Search results

Summary of Contents for TX-I/O

Reviews:

Related manuals for TX-I/O

Brands by name

Popular brands