Siemens TX-I/O User Manual Download | Manualshive

Page: 47 / 94

background image

47 / 94

Siemens

TX-I/O PROFINET BIM V1.0

CM110564en_02

Building Technologies

Parameters

23.09.2010



Switch from local override to automatic:

The automatic process value becomes valid once the Profinet I/O controller
writes a new value.

Possible values

Description

Selected Enabled
Not selected

Disabled

4.9.6

Local Override Mode

Parameter for defining the type of 'local override' signal.

A logical '1' is usually interpreted as 'active'. However, it is possible for migrations
to interpret a logical '0' as 'active'.

The following assignments apply here:

Value

Input

Local override

Active 1

Active

Inactive 0 Active
Active 0

Inactive

Inactive 1 Inactive

4.9.7

Process Data

The allocation of process data and the channel status information of multistate
output-configured channels for local override are described in 'Process Data
Channel Mapping' for the corresponding TX-I/O module.

[MOValue] represents the current status. During the 'off' pulse, [MOValue] changes
to '0'. During the delay period [MinOffTime] the current [MOValue] differs from the
commanded value.

If [MOValue] is invalid (i.e., no corresponding channel is available), then



a quality error message (Reliability) is generated:

[Quality = MULTISTATE_FAULT]



a backup value becomes valid according to the value in [BackupMode].

4.9.8

Channel Diagnosis

Alarm type

Cause / solution

Invalid

Check the module configuration and parameterization

No_Output

Operating voltage too low -> check the power

Multistate_Fault

Mapping error -> check the multistate functions

If the TX-I/O BIM has the status 'Masterdown'

after a start

, no new output pulses

are generated, regardless of the value [BackupMode].

If local override is active after starting the TX-I/O, an output pulse defined by
[MOValue] will be generated.

Definition,

addition

Read MOValue

Invalid MO Value

Masterdown

Local override

«
...
45
46
47
48
49
...
»

Summary of Contents for TX-I/O































































































Reviews:

No comments

Related manuals for TX-I/O

Peltor DECT-Com II

Brand: 3M Pages: 17

Brand: 3M Pages: 10

Brand: 3M Pages: 32

Brand: 3M Pages: 29

Audio Greeter A300

Brand: 3M Pages: 4

Brand: 3M Pages: 18

Brand: 3M Pages: 29

Brand: Dahua Pages: 23

VTO2000A Series

Brand: Dahua Pages: 41

Brand: Dahua Pages: 85

Brand: latch Pages: 8

Brand: EAW Pages: 9

Brand: ICP DAS USA Pages: 7

Brand: ICP DAS USA Pages: 28

I-2533CS Series

Brand: ICP DAS USA Pages: 8

AZ8350 - Cd Radio Cass Recorder

Brand: Magnavox Pages: 18

Brand: MAJORITY Pages: 32

Brand: Patton Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands