Siemens TX-I/O User Manual Download Page 18

Page: 18 / 94

18 / 94

Siemens

TX-I/O PROFINET BIM V1.0

CM110564en_02

Building Technologies

Engineering

23.09.2010

Import Profinet BIM

to the Profinet network by drag&drop of the

TXB1.Profinet BIM.

After releasing the mouse button, the Profinet BIM is inserted and is displayed
in the Profinet network.

Note

When clicking the Profinet BIM, the slot allocation and I/O addresses are
displayed in detail in the station window.

7. Rightclick

I/O bar

> context menu: Object Properties

Opens the PROFINET I/O system properties dialog field.

Update time

tab: mark the device >

Edit

button

Opens the Edit update time/mode dialog field.

9. Set

the

update time

256 ms

using the dropdown list box.

This is a recommendation. A higher clock rate makes no sense since the
island bus is clocked at 512 ms.

10. Close

with

OK.

3.3

Engineering the Profinet BIM with the
SIMATIC Manager

The Profinet BIM is a modular device. It supports specific TX-I/O modules and their
corresponding channel functions.

TXM1.8D TXM1.8U TXM1.8X TXM1.6R

TXM1.6RL

TXM1.16D TXM1.8U-ML

TXM1.8X-ML TXM1.6R-M TXM1.8P

The following sections explain the engineering procedure in terms of



module configuration



submodule configuration and



parameterization.



Profinet BIM supports 120 slots. TX-I/O modules can be inserted in any slot

within this range (1...120).

Supported TX-I/O
modules

Supported slots

Summary of Contents for TX-I/O































































































Search results

Summary of Contents for TX-I/O

Reviews:

Related manuals for TX-I/O

Brands by name

Popular brands

Siemens TX-I/O, User Manual

Search results

Summary of Contents for TX-I/O

Reviews:

Related manuals for TX-I/O

Brands by name

Popular brands