Siemens TX-I/O User Manual Download Page 73

Page: 73 / 94

73 / 94

Siemens

TX-I/O PROFINET BIM V1.0

CM110564en_02

Building Technologies

Module Data

23.09.2010

7 Module

Data

This section explains how the input/output channels of the TX-I/O modules are
mapped to the SIMATIC S7 input/output addresses.

7.1

General

Every newly added ('plugged') module must be addressed. This procedure is not
similar for all modules. We distinguish between



binary input/output modules and



analog and multistate modules.

The addressing takes place on the module (subslot 1) according to the binary
channel of the module.

The SIMATIC S7 address of a binary input/output is obtained from the
parameterized address of the module plus the offset specified in the table.

Example

Module input address

Channel 4

0.3

(byte 0, bit 3)

SIMATIC S7 address

E 50.3

The addressing takes place on the submodule (subslots 2…1) according to the
analog or multistate function.

The SIMATIC S7 address of the analog/multistate input/output is obtained directly
from the subslot address parameterized in the channel.
The offsets specified in the tables are also assigned.

Example

Submodule input address

SIMATIC S7 address

PEW 26

The SIMATIC addresses of the channel process data are given below.

Local override information is indicated separately for each individual TX-I/O

module.

Binary modules

Analog and multistate
modules

Summary of Contents for TX-I/O































































































Search results

Summary of Contents for TX-I/O

Reviews:

Related manuals for TX-I/O

Brands by name

Popular brands

Siemens TX-I/O, User Manual

Search results

Summary of Contents for TX-I/O

Reviews:

Related manuals for TX-I/O

Brands by name

Popular brands