Siemens TX-I/O User Manual Download Page 27

Page: 27 / 94

27 / 94

Siemens

TX-I/O PROFINET BIM V1.0

CM110564en_02

Building Technologies

Parameters

23.09.2010

4.2

Binary Input (Pulse)

BI_PULSE

(SIMATIC Manager hardware catalog)

Pulse binary input = input for detecting/processing continuous status changes in
applied signals.

A floating contact or electronic switch is connected with the binary pulse input. The
object carries out a cyclical check at the input. Every change from one stable status
to the other is detected.

Note

If the Profinet communication is missing, a short pulse is indicated with the

relevant LED for each pulse at the input.

4.2.1

Pulse Length

Parameter for defining the pulse length.

Value range

Unit

0..255 0.1

4.2.2

Contact

Parameters for defining the contact type.

Possible values

Description

NO Contact

"Not Open" contact

NC Contact

"Not Closed" contact

Status

NO contact

NC contact

Contact position

LED
indication

Process
value

LED
indication

Process
value

Contact closed >
open

Pulse
0 > 1 > 0

0 0

Contact open >
closed

0 0 Pulse

0 > 1 > 0

Pulse
0 > 1 > 0

Representation

Definition,

addition

Definition,

addition

Parameter

Definition,

addition

Parameters

Functional overview

Summary of Contents for TX-I/O































































































Search results

Summary of Contents for TX-I/O

Reviews:

Related manuals for TX-I/O

Brands by name

Popular brands

Siemens TX-I/O, User Manual

Search results

Summary of Contents for TX-I/O

Reviews:

Related manuals for TX-I/O

Brands by name

Popular brands