Siemens SITRANS L Series Operating Instructions Manual Download Page 67

Page: 67 / 106

Setup with the integrated HMI
7.8.3 Circuit test

Max. measured distance

MAX DISTANCE:

Displays the value of the maximum measured distance. The value may reset if the

unit is changed.

Minimum electronics temperature

TR TEMP MIN:

Displays the value of the minimum transmitter temperature.

Maximum electronics temperature

TR TEMP MAX:

Displays the value of the maximum transmitter temperature.

7.8.3

Circuit test

Simulation current output

LOOP TEST:

A simulated value can be set to test the operation and mA connections during setup

or maintenance of the unit.

Note

The simulated value of the current output influences the output to the control

system.

Press the key

←

to stop and terminate the circuit test.

SITRANS LR150

Operating Instructions, 08/2020,

A5E50352155

Summary of Contents for SITRANS L Series











































































































Search results

Summary of Contents for SITRANS L Series

Reviews:

Siemens SITRANS L Series, Operating Instructions Manual, Page: 67 / 106

Search results

Summary of Contents for SITRANS L Series

Reviews: