Siemens SITRANS L Series Operating Instructions Manual Download Page 60

Page: 60 / 106

Setup with the integrated HMI

7.7.5 Volume

Note

This menu is only visible on the device if it is configured.

Vessel shape

Sets the vessel shape and allows the device to calculate the volume instead of the

level.

Setting

Selection

Description
Other required parameters

LINR

Linear vessel
Upper scaling point

CONIC

Conical vessel bottom
Upper scaling point, vessel

dimension A

FLAT SLOPE

Container with flat sloping

bottom
Upper scaling point, vessel

dimension A

CYLIN

Cylindrical vessel
Upper scaling point

VOLUME

VESSEL SHAPE

CUSTM

Custom

Vessel dimension A

VESSSEL DIM A:

Adjusts the height of the vessel bottom in case of a conical, parabolic, spherical

or flat sloping bottom. Sets the height of the end piece for a horizontal tank with

parabolic ends.

Volume unit

Sets the measuring units for the volume.

Setting

Selection

Description

Cubic metre

Litres

US gallons

VOLUME

VOLUME UNITS

IGa

British Gallons

Upper scaling point

Sets the maximum scaled measured value.

SITRANS LR150

Operating Instructions, 08/2020,

A5E50352155

Summary of Contents for SITRANS L Series











































































































Search results

Summary of Contents for SITRANS L Series

Reviews:

Siemens SITRANS L Series, Operating Instructions Manual, Page: 60 / 106

Search results

Summary of Contents for SITRANS L Series

Reviews: