Siemens SITRANS L Series Operating Instructions Manual Download Page 61

Page: 61 / 106

Setup with the integrated HMI
7.7.6 Volume flow

7.7.6

Volume flow

Note

This menu is only visible on the device if it is configured.

Lower calibration point

LOWER CAL POINT:

Sets the distance from the transmitter reference point to the lower calibration point.

Upper calibration point

UPPER CAL POINT:

Sets the distance from the transmitter reference point to the upper calibration point.

Measuring structure

Sets the version of the measuring structure used.

Setting

Selection

Description
Other required parameters

PBFLM

Palmer-Bowlus flume

RWRC

Venturi flume, trapezoidal

weir, rectangular overfall

TPVWR

V-Notch, triangular weir

VOLUME FLOW

FLUME TYPE

CUSTM

Custom

Flow unit

Sets the measurement units for the volume flow.

Setting

Selection

Description

Cubic metre

L/min

Litres

Ga/min

US gallons

VOLUME FLOW

VFLOW UNITS

IGa/min

British Gallons

SITRANS LR150

Operating Instructions, 08/2020,

A5E50352155

Summary of Contents for SITRANS L Series











































































































Search results

Summary of Contents for SITRANS L Series

Reviews:

Siemens SITRANS L Series, Operating Instructions Manual, Page: 61 / 106

Search results

Summary of Contents for SITRANS L Series

Reviews: