manualshive.com logo in svg

Siemens SINUMERIK 802D sl, Function Manual, Page: 336 / 462

Share
Download
Siemens SINUMERIK 802D sl Function Manual Download Page 336

Rotary Axes (R2) 

 

19.3 Programming rotary axes 

 

Turning, Milling, Nibbling 

336

 

Function Manual, 11/2012, 6FC5397-1CP10-5BA0 

MD30320 DISPLAY_IS_MODULO = 0:  
Absolute-position display would, in the case of a positive direction of rotation, for example, 

result in +360° being displayed after one revolution, +720° after two revolutions, etc., in 

contrast to the modulo 360° display. In this case, the display range is limited by the control in 

accordance with the linear axes.  

19.3

 

Programming rotary axes 

 

 

Note 
For general information about programming, please see: 
Reference: 
/BP_/ Operation and Programming 

 

 

19.3.1

 

Rotary axis with active modulo conversion 

Absolute programming (AC, ACP, ACN, G90)  

Example with ACP: C=ACP(5.33) , general: axis name =ACP(value)  
●

 

The value identifies the target position of the rotary axis in a range from 0 to 359.999°. 

Alarm 16830, "Incorrect modulo position programmed", is output for values with a 

negative sign or ≥ 360°. 

●

 

ACP (positive) and ACN (negative) define the traversing direction of the rotary axis 

unambiguously (irrespective of actual position). 

●

 

When programming with AC or with G90, the traversing direction depends on the actual 

position of the rotary axis. If the target position is greater than the actual position, the axis 

traverses in the positive direction, otherwise it traverses in the negative direction. 

●

 

Use of ACP and ACN: With asymmetrical workpieces, it must be possible to define the 

traversing direction in order to prevent collisions during rotation. 

Absolute programming along the shortest path (DC) 

Example with DC: C=DC(25.3), general: axis name =DC(value) 
●

 

The value identifies the target position of the rotary axis in a range from 0 to 359.999 

degrees. Alarm 16830, "Incorrect modulo position programmed", is output for values with 

a negative sign or ≥ 360°. 

●

 

With DC (Direct Control), the rotary axis approaches the programmed absolute position 

within one revolution along the shortest path (traversing movement max. ± 180°). 

Summary of Contents for SINUMERIK 802D sl















































































































































































































































































































































































































































































Reviews:

No comments