Siemens MOTOX BA 2010 Page 47 Operating Instructions Manual Download

Page: 47 / 124

Installation

4.10 Removing and installing the shaft-mounted gearbox

BA 2010
Operating Instructions, 02/2018, A5E38093846A/RS-AC

4.10.3.2

Pulling off the shrink disk

Procedure

Release the tightening bolts

③

one after the other by a ¼ turn each time using a wrench.

Do not completely remove the bolts.

Pull the shrink disk off the hollow shaft.

Sizes 38 - 208:

If the outer ring does not come away from the inner ring, remove some of the tightening bolts

and insert them into neighboring back-off threads.
You have pulled the shrink disk off the hollow shaft.

4.10.3.3

Cleaning and lubricating shrink disks

Soiled shrink disks must be cleaned and regreased prior to fitting.
Shrink disks that have been released need not be disassembled and regreased before being

retensioned.

Procedure

Only grease the inner friction surfaces of the shrink disks. To do this, use a solid lubricant

with a friction coefficient of μ

= 0.04.

Use a paste containing MoS

to grease the bolts, applying the paste to the thread and

underneath the head.

Clean the shrink disk.

Table 4- 4

Lubricants for shrink disks

Lubricant

Sold as

Manufacturer

Molykote 321 R (lubricant paint) Spray

DOW Corning

Molykote spray (powder spray)
Molykote G Rapid

Spray or paste

Molykombin UMFT 1

Spray

Klüber Lubrication

Unimily P5

Powder

Aemasol MO 19 P

Spray or paste

A. C. Matthes

Summary of Contents for MOTOX BA 2010





























































































































Search results

Summary of Contents for MOTOX BA 2010

Reviews:

Related manuals for MOTOX BA 2010

Brands by name

Popular brands

Siemens MOTOX BA 2010, Operating Instructions Manual

Search results

Summary of Contents for MOTOX BA 2010

Reviews:

Related manuals for MOTOX BA 2010

Brands by name

Popular brands