Siemens MOTOX BA 2010 Page 39 Operating Instructions Manual Download | Manualshive

Page: 39 / 124

background image

Installation

4.10 Removing and installing the shaft-mounted gearbox

BA 2010
Operating Instructions, 02/2018, A5E38093846A/RS-AC

37

Procedure

1.

Undo the screws

①

and remove the protection cover

②

.

2.

Fit the output shaft.

3.

Using a suitable cleaning agent, clean the contact surface of the protection cover

②

on

the gearbox.

4.

With the protection cover for shrink disk in the ATEX version, ensure that the O-ring

⑤

is

correctly seated.

5.

Coat the supporting surface of the protection cover

②

with a suitable sealing agent.

6.

Screw on the protection cover

②

.

7.

Protect all remaining bare areas with a suitable permanent anti-corrosive agent.

You have now installed the protection cover for operation.

4.10

Removing and installing the shaft-mounted gearbox

4.10.1

General information on installing the shaft-mounted gearbox

NOTICE
Damage to shaft sealing rings caused by solvent
Avoid any contact of solvent or benzine with the shaft sealing rings.

NOTICE
Subjecting stress to the hollow shaft causes bearing failure
Skewing or stressing the hollow shaft increases the loading. This can cause bearing failure.
The hollow shaft must be flush with the machine shaft to avoid misalignment.
Do not subject the hollow shaft to axial and radial stress.

NOTICE
For shrink disks:

Lubricants in the area between the hollow shaft and machine shaft impair torque

transmission
Keep the bore in the hollow shaft and the machine shaft completely grease-free.
Do not use impure solvents and soiled cleaning cloths.

«
...
37
38
39
40
41
...
»

Summary of Contents for MOTOX BA 2010





























































































































Reviews:

No comments

Related manuals for MOTOX BA 2010

Brand: Modulate Pages: 2

Brand: Ultimaker Pages: 38

Brand: A&D Pages: 2

Brand: A&D Pages: 176

Brand: TC Electronic Pages: 2

Brand: Bahco Pages: 131

Brand: Bahco Pages: 126

Brand: Danelec Pages: 67

Brand: unios Pages: 2

Brand: M-Audio Pages: 3

Brand: Xtralis Pages: 26

FUSION APOLLO MS-WB675

Brand: Garmin Pages: 18

Brand: Rapid Shape Pages: 12

MultiFill 003-561-005

Brand: Hanskamp Pages: 20

Brand: Jefferson Pages: 2

Brand: Lighthouse Pages: 2

Brand: Varan Motors Pages: 70

Brand: Nolangroup Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands