Siemens MOTOX BA 2010 Page 23 Operating Instructions Manual Download | Manualshive

Page: 23 / 124

background image

BA 2010
Operating Instructions, 02/2018, A5E38093846A/RS-AC

21

Incoming goods, transport, and storage

3

3.1

Incoming goods

NOTICE
Transport damage impairs correct functioning
Do not commission faulty gearboxes or geared motors.

Note
Do not open or damage parts of the packaging that preserve the product.

Note
Check that the technical specifications are in accordance with the purchase order.
Inspect the delivery immediately on arrival for completeness and any transport damage.
Notify the freight company of any damage caused during transport immediately (this is the

only way to have damage rectified free of charge). Siemens AG will not accept any claims

relating to items missing from the delivery and which are submitted at a later date.

The gearbox or geared motor is delivered in a fully assembled condition. Additional items are

sometimes delivered packaged separately.
The products supplied are listed in the dispatch papers.

«
...
21
22
23
24
25
...
»

Summary of Contents for MOTOX BA 2010





























































































































Reviews:

No comments

Related manuals for MOTOX BA 2010

Brand: DARAY Pages: 24

Brand: Jafar Pages: 9

Brand: Datalogic Pages: 48

Brand: PageFlip Pages: 32

Brand: ICELED Pages: 4

Brand: Facom Pages: 4

Brand: FaceLake Pages: 2

Brand: FabiaTech Pages: 2

Brand: FabiaTech Pages: 77

Brand: Xtool Pages: 51

Brand: H-TEC Education Pages: 16

Brand: H-TEC Education Pages: 12

ProFire Lightbridge

Brand: M-Audio Pages: 8

Brand: M-Audio Pages: 36

Brand: Waterpik Pages: 2

HQ Power VDL25BM

Brand: Velleman Pages: 3

Brand: iGuzzini Pages: 36

AQUIS ULTRAFLOW

Brand: Waterous Pages: 56

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands