Siemens MOTOX BA 2010 Page 14 Operating Instructions Manual Download

Page: 14 / 124

General information and safety notes

1.6 Particular types of hazards

BA 2010

Operating Instructions, 02/2018, A5E38093846A/RS-AC

1.6

Particular types of hazards

WARNING

Extreme surface temperatures
Hot surfaces over +55 °C pose a burn risk.
Cold surfaces below 0 °C pose a risk of damage due to freezing.
Do not touch the gearbox without protection.

WARNING

Hot, escaping oil
Before starting any work wait until the oil has cooled down to below +30 °C.

WARNING

Poisonous vapors when working with solvents
Avoid breathing in vapors when working with solvents.
Ensure adequate ventilation.

WARNING

Risk of explosion when working with solvents
Ensure adequate ventilation.
Do not smoke!

WARNING

Risk of eye injury
Rotating parts can throw off small foreign particles such as sand or dust.
Wear protective eyewear!

In addition to the prescribed personal protection gear, also wear suitable protective gloves

and safety glasses.

Summary of Contents for MOTOX BA 2010





























































































































Search results

Summary of Contents for MOTOX BA 2010

Reviews:

Related manuals for MOTOX BA 2010

Brands by name

Popular brands

Siemens MOTOX BA 2010, Operating Instructions Manual

Search results

Summary of Contents for MOTOX BA 2010

Reviews:

Related manuals for MOTOX BA 2010

Brands by name

Popular brands