Siemens MOTOX BA 2010 Page 122 Operating Instructions Manual Download

Page: 122 / 124

Explanations

12.3 EC/EU Declaration of Conformity

BA 2010

120

Operating Instructions, 02/2018, A5E38093846A/RS-AC

Conformance with the regulations laid down in this legislation is proven by fully complying

with EN 60034-30: 2009.
The designated product is intended for installation in a machine. Commissioning is prohibited

until it has been established that the end product conforms with Directive 2006/42/EC.
First time that the CE marking was applied: 2016

Tübingen, July 1, 2017
Georg Böing

Head of Research & Development

Florian Hanisch

Vice President Lead Factory Simogear

This declaration certifies compliance with the Directives named above, but does not

guarantee any specific properties or durability in the sense of § 443 BGB (Section of the

German Civil Code governing guarantee provisions). Please observe the safety information

in the supplied product documentation.

Summary of Contents for MOTOX BA 2010





























































































































Search results

Summary of Contents for MOTOX BA 2010

Reviews:

Related manuals for MOTOX BA 2010

Brands by name

Popular brands

Siemens MOTOX BA 2010, Operating Instructions Manual

Search results

Summary of Contents for MOTOX BA 2010

Reviews:

Related manuals for MOTOX BA 2010

Brands by name

Popular brands