Siemens MOTOX BA 2010 Page 66 Operating Instructions Manual Download

Page: 66 / 124

Service and maintenance

8.2 Checking and changing lubricants

BA 2010

Operating Instructions, 02/2018, A5E38093846A/RS-AC

8.2.5

Checking the oil quality

Signs of changes in the oil can be seen with the naked eye. Fresh oil is clear to the eye and

has a typical smell and a specific product color. Clouding or a flocculent appearance

indicates water and / or contamination. A dark or black color indicates residue, serious

thermal decomposition or contamination.

Observe the symbols in the type of construction diagrams, see Mounting positions

(Page 87):

Ventilation

Oil filling

Oil level

Procedure

Allow the geared motor to run for a short time. Wear and contaminant particles are visible

in the oil shortly after shutting down.

Switch off the power supply to the drive unit.

Remove the sealing element at one of the points marked with the symbols listed above.

Remove some oil, using a suction pump and a flexible hose, for example.

Check the condition of the sealing ring on the sealing element and replace the sealing

ring if necessary.

Seal the gearbox with the sealing element.

Check the oil for abnormalities. If you detect any abnormalities, change the oil

immediately.

Check the oil level.

Rectify the oil level if necessary and check it again.

You have now checked the oil quality.

Summary of Contents for MOTOX BA 2010





























































































































Search results

Summary of Contents for MOTOX BA 2010

Reviews:

Related manuals for MOTOX BA 2010

Brands by name

Popular brands

Siemens MOTOX BA 2010, Operating Instructions Manual

Search results

Summary of Contents for MOTOX BA 2010

Reviews:

Related manuals for MOTOX BA 2010

Brands by name

Popular brands