Siemens MOTOX BA 2010 Page 12 Operating Instructions Manual Download | Manualshive

Page: 12 / 124

background image

General information and safety notes

1.4 Obligations of the user

BA 2010

10

Operating Instructions, 02/2018, A5E38093846A/RS-AC

Note
The performance data assumes an ambient temperature of -20° C to +40° C and an

installation altitude of up to 2000 m above sea level.
In the case of other ambient temperatures and installation altitudes, please contact Technical

Support.

The gearboxes are designed only for the area of application described in Section Technical

data (Page 81).

Do not operate the gearboxes outside the specified performance limits.

Any different operating conditions require new contractual agreements.
Do not climb on the gearbox. Do not place any objects on the gearbox.

1.4

Obligations of the user

The operator must ensure that all persons assigned to work on the geared motor have read

and understood these operating instructions and that they follow them in all points in order

to:

●

Eliminate the risk to life and limb of users and other persons.

●

Ensure the operational safety of the geared motor.

●

Avoid disruptions and environmental damage through incorrect use.

Note the following safety information:
Shut down the geared motors and disconnect the power before you carry out any work on

them.
Make sure that the drive unit cannot be turned on accidentally, e.g. lock the key-operated

switch. Place a warning notice at the drive connection point which clearly indicates that work

is in progress on the geared motor.
Carry out all work with great care and with due regard to "safety".
For all work, observe the relevant regulations for work safety and environment protection.
Read the instructions on the rating plates attached to the geared motor. The rating plates

must be kept free from paint and dirt at all times. Replace any missing rating plates.
In the event of changes during operation, switch off the drive unit immediately.
Take appropriate protective measures to prevent accidental contact with rotating drive parts,

such as couplings, gear wheels or belt drives.

«
...
10
11
12
13
14
...
»

Summary of Contents for MOTOX BA 2010





























































































































Reviews:

No comments

Related manuals for MOTOX BA 2010

Brand: Landi Renzo Pages: 16

Brand: IBM Pages: 163

SimMan 3G Trauma

Brand: laerdal Pages: 16

Brand: laerdal Pages: 16

Brand: laerdal Pages: 60

Brand: laerdal Pages: 4

Resusci Anne Simulator

Brand: laerdal Pages: 8

Nursing Baby VitalSim

Brand: laerdal Pages: 15

Brand: Pari Pages: 12

Brand: laerdal Pages: 2

Brand: laerdal Pages: 104

Brand: laerdal Pages: 33

Brand: Lafayette Pages: 2

Brand: Teac Pages: 76

Brand: Teac Pages: 3

Brand: Teac Pages: 50

Brand: Teagle Pages: 2

Brand: U-Line Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands