Siemens MOTOX BA 2010 Page 44 Operating Instructions Manual Download | Manualshive

Page: 44 / 124

background image

Installation

4.10 Removing and installing the shaft-mounted gearbox

BA 2010

42

Operating Instructions, 02/2018, A5E38093846A/RS-AC

4.10.3

Shrink disk

4.10.3.1

Mounting the shrink disk

WARNING

Risk of injury due to freely rotating parts
Fit a cover cap or protection cover.

NOTICE
Lubricants in the shrink disk seat impair torque transmission
Keep the bore in the hollow shaft and the machine shaft completely grease-free.
Do not use impure solvents and soiled cleaning cloths.

NOTICE
Plastic deformation of the hollow shaft caused by tightening the tightening bolts
Plastic deformation of the hollow shaft when tightening the tightening bolts before fitting the

machine shaft.
First fit machine shaft. Then tighten the tightening bolts.

NOTICE
Avoid overloading the individual bolts
Do not exceed the maximum tightening torque for tightening bolt.
Size 28:

Tighten tightening bolts

③

.

Sizes 38 - 208:

What is of prime importance is that the end faces of the outer ring

①

and inner ring

②

are

flush with one another. If they are not flush with one another when tensioning, check the

tolerance of the insert shaft.

Note
The shrink disk is delivered ready for installation.
Do not dismantle the shrink disk before initial fitting.

«
...
42
43
44
45
46
...
»

Summary of Contents for MOTOX BA 2010





























































































































Reviews:

No comments

Related manuals for MOTOX BA 2010

Brand: MacDon Pages: 89

Brand: Yates Pages: 2

Brand: JAC Pages: 100

Brand: York Fitness Pages: 34

Brand: Landoll Pages: 34

WJHD100 - DIGITAL DISC RECORDE

Brand: Panasonic Pages: 7

Brand: Velocitek Pages: 81

ABS-Lock X-Flat

Brand: ABS Pages: 8

ABS-Lock X-DURCH

Brand: ABS Pages: 8

Brand: ABS Pages: 8

Brand: York Fitness Pages: 20

Brand: Pablo Pages: 7

Brand: M-system Pages: 3

Brand: M-system Pages: 5

Brand: MA Pages: 2

Brand: PAT Pages: 44

Brand: Park Tool Pages: 4

Brand: Qlight Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands