Siemens MOTOX BA 2010 Page 25 Operating Instructions Manual Download

Page: 25 / 124

Incoming goods, transport, and storage

3.2 Transport

BA 2010
Operating Instructions, 02/2018, A5E38093846A/RS-AC

3.2.2

Fastening for suspended transport

WARNING

Inadequately secured gearbox or geared motors
Observe the maximum load for the transport eye

③

of the bevel helical gearbox or the

eyebolt axis

④

Use only the transport eye

③

or eyebolt

④

of the gearbox to transport the gearbox or

geared motor.
Do not use the integrally cast lifting eyes

①

on the motor for transport because of the risk

of breaking. Only use the eyebolt

②

on the motor to transport the motor prior to mounting

or following removal.
If necessary, use additional, suitable lifting accessories for transport or during installation.
When attaching by a number of chains and ropes just two strands must be sufficient to bear

the entire load. Secure lifting accessories against slipping.

NOTICE
Do not rig eyebolts to the front threads at the shaft ends for transportation purposes

Transport eye on the bevel helical gearbox

Eyebolt on the helical gearbox, parallel shaft

gearbox, helical worm gearbox

①

Integrally cast eye on the motor

②

Eyebolt on the motor

③

Transport eye on the bevel helical gearbox

④

Eyebolt on the gearbox

Figure 3-1

Fastening the gearbox or geared motor for suspended transport

Summary of Contents for MOTOX BA 2010





























































































































Search results

Summary of Contents for MOTOX BA 2010

Reviews:

Related manuals for MOTOX BA 2010

Brands by name

Popular brands

Siemens MOTOX BA 2010, Operating Instructions Manual

Search results

Summary of Contents for MOTOX BA 2010

Reviews:

Related manuals for MOTOX BA 2010

Brands by name

Popular brands