Siemens MOTOX BA 2010 Page 121 Operating Instructions Manual Download

Page: 121 / 124

Explanations

12.3 EC/EU Declaration of Conformity

BA 2010
Operating Instructions, 02/2018, A5E38093846A/RS-AC

119

12.3

EC/EU Declaration of Conformity

Document No. A5E37802261AB

Manufacturer:

Siemens AG

Division Digital Factory DF MC

Address:

Bahnhofstraße 40, 72072 Tübingen, Germany

Product designation:

Low-voltage motors, types

Sizes:

LA/LAI 63 - 160, LG/LGI 180 - 315

Where relevant in conjunction with

MOTOX gearbox types:

E, Z, D, F, B, BH, K, KH, C, CH

The designated product complies with the regulations of the following European Directive:
Directive 2014/35/EU, OJ L 96/357, 29.3.2014, of the European Parliament and of the

Council of 26 February 2014 on the harmonisation of the laws of the Member States relating

to the making available on the market of electrical equipment designed for use within certain

voltage limits (Low-Voltage Directive).
Conformance with the regulations laid down in these Directives is proven by fully complying

with the following standards:

•

EN 60034-1: 2010

•

EN 60034 - all other relevant sections in the latest version in each

case

•

EN 60664-1: 2007

•

EN 60204-1: 2006 +A1: 2009 +AC: 2010

EC/EU Declarations of Conformity and / or manufacturer's declarations for all

subassemblies, integrated and add-on units are available.
Specifically, these are:

●

Electromagnetic brakes L, ZL, P, FDX, FDW, KFB with connected accessories such as

rectifiers and switching devices

●

External fan units F

●

Shaft encoders IA, IM, IN, RE, TA

The designated product also complies with the regulations of the following legal acts:

●

Commission Regulation (EC) No 640/2009 of 22 July 2009 implementing

Directive 2005/32/EC of the European Parliament and of the Council with regard to

ecodesign requirements for electric motors.

●

Directive 2009/125/EC of the European Parliament and of the Council of 21 October 2009

establishing a framework for the setting of ecodesign requirements for energy-related

products.

●

Commission Regulation (EU) No 4/2014 of 6 January 2014 amending Regulation (EC)

No 640/2009 implementing Directive 2005/32/EC of the European Parliament and of the

Council with regard to ecodesign requirements for electric motors.

Summary of Contents for MOTOX BA 2010





























































































































Search results

Summary of Contents for MOTOX BA 2010

Reviews:

Related manuals for MOTOX BA 2010

Brands by name

Popular brands

Siemens MOTOX BA 2010, Operating Instructions Manual

Search results

Summary of Contents for MOTOX BA 2010

Reviews:

Related manuals for MOTOX BA 2010

Brands by name

Popular brands