Siemens MOTOX BA 2010 Page 98 Operating Instructions Manual Download

Page: 98 / 124

Technical data

10.6 Oil quantities

BA 2010

Operating Instructions, 02/2018, A5E38093846A/RS-AC

10.5.6

Tandem gearboxes - Intermediate helical gearboxes

Note
In a horizontal operating position the bulging part of the housing of the 2nd gearbox

generally faces vertically downwards.

Note
Where tandem gearboxes are concerned, each individual gearbox is to be considered

separately.
Gearbox sizes 28 and 38 on the 2nd gearbox are lubricated for life.
Screw plugs are not provided.

Horizontal operating position

Vertical operating position

Main gearbox

2nd gearbox (intermediate helical gearbox)

On opposite side

②

2-stage gearbox

③

3-stage gearbox

Figure 10-21 Operating position for tandem gearbox

10.6

Oil quantities

NOTICE
Incorrect oil quantities damage the gearbox
The oil quantities listed in the tables are guide values for changing the oil.

They are used, for example, for lubricant storage and procurement. The precise values

depend on the number of stages and transmission ratio of the gearbox.
Check the oil level before commissioning.

Summary of Contents for MOTOX BA 2010





























































































































Search results

Summary of Contents for MOTOX BA 2010

Reviews:

Related manuals for MOTOX BA 2010

Brands by name

Popular brands

Siemens MOTOX BA 2010, Operating Instructions Manual

Search results

Summary of Contents for MOTOX BA 2010

Reviews:

Related manuals for MOTOX BA 2010

Brands by name

Popular brands