Siemens MOTOX BA 2010 Page 79 Operating Instructions Manual Download

Page: 79 / 124

Service and maintenance

8.10 Inspecting the gearbox

BA 2010
Operating Instructions, 02/2018, A5E38093846A/RS-AC

The general tolerance for the tightening torque is 10 %. The tightening torque is based on a

friction coefficient of μ

= 0.14.

Table 8- 8

Tightening torques for fastening bolts

Thread size

Tightening torque for strength class
8.8

10.9

12.9

[Nm]

M10

M12

120

145

M16

210

295

355

M20

450

580

690

M24

750

1 000

1 200

M30

1 500

2 000

2 400

M36

2 500

3 600

4 200

8.10

Inspecting the gearbox

Carry out a scheduled inspection of the gearbox once a year in accordance with the possible

criteria listed in General notes about maintenance work (Page 57).
Check the gearbox in accordance with the criteria set out in General information and safety

notes (Page 7).
Touch up damaged paintwork carefully.

8.11

Maintenance of the friction clutch

Note
Check the condition of the friction clutch initially after 500 operating hours and then at least

once yearly and after every blockage of the machine.

If necessary, readjust the friction torque or replace the wearing parts, e.g., friction lining and

bushes. Friction linings must always be replaced in pairs. We recommend replacing worn

bushes in sets.
Please refer to the relevant operating instructions for the clutch.

Summary of Contents for MOTOX BA 2010





























































































































Search results

Summary of Contents for MOTOX BA 2010

Reviews:

Related manuals for MOTOX BA 2010

Brands by name

Popular brands

Siemens MOTOX BA 2010, Operating Instructions Manual

Search results

Summary of Contents for MOTOX BA 2010

Reviews:

Related manuals for MOTOX BA 2010

Brands by name

Popular brands