Siemens MICROMASTER Reference Manual Download Page 46 | Manualshive

Page: 46 / 78

background image

COMBIMASTER & MICROMASTER Integrated
REFERENCE MANUAL

©

Siemens plc. 1999

| G85139-H1731-U300-D2

45

COMBIMASTER

CB155

T CONNECTOR

COMBIMASTER

CB155

T CONNECTOR

COMBIMASTER

CB155

T CONNECTOR

TERMINATOR

BUS MASTER

INTERCONNECTING CABLES - One or
more cables joined by cable links.

Cable A

Cable B

Cable C

SK200

SK200

SK200

Figure 11 Typical PROFIBUS Installation, Showing Use Of Accessories

PROFIBUS Component

Order Number

Drawing Reference

CM PROFIBUS module CB155

Note: For CS B Issue A units :-

6SE9996-0XA18

6SE9996-0XA20

Includes Cable A

CM PROFIBUS T connector

6SE9996-0XA21

Includes Cable B

CM PROFIBUS terminator

6SE9996-0XA22

CM PROFIBUS cable 1m

6SE9996-0XA23

Cable C

CM PROFIBUS cable 5m

6SE9996-0XA24

Cable C

CM PROFIBUS cable 10m

6SE9996-0XA25

Cable C

CM PROFIBUS cable link

6SE9996-0XA26

Used for joining lengths of cable C

1. A clear text operator panel

(OPM2) is required to set the
COMBIMASTER parameters
prior to connecting the
PROFIBUS module.

2.

The PROFIBUS Module may only

be connected or disconnected
from the drive when the drive is
powered off.

3.

The PROFIBUS module must only

be connected to the drive with the
cable supplied for the purpose.

4.

The PROFIBUS module cannot be

used simultaneously with the
Clear Text Display module.

The data structure for communication over
PROFIBUS-DP can be either PPO type 1 or
PPO type 3 as specified in VDI/VDE 3689.
This means in practice that process data
(control words, set-point in the transmitted
telegram and status words, actual values in the
received telegram) is always sent.

Parameter data exchange may, however, be
blocked if bus or PLC memory space is at a
premium. The data structure and thus the
PPO type is normally specified by the bus
master. If no PPO type is specified (e.g. if a
combined DP/FMS bus master is used), then
the default PPO type is type 1 (parameter data
enabled). Parameter write access over the
serial link can be enabled or blocked as
required.

For more detailed Information ,
refer to Profibus Manual

«
...
44
45
46
47
48
...
»

Summary of Contents for MICROMASTER















































































Reviews:

No comments

Related manuals for MICROMASTER

Brand: LEDone Pages: 3

Brand: National Instruments Pages: 30

Brand: GU Pages: 13

Brand: YASKAWA Pages: 172

Brand: Commodore Pages: 48

Brand: JVC Pages: 1

Brand: Samsung Pages: 10

Brand: Samsung Pages: 10

Brand: Samsung Pages: 10

Brand: Samsung Pages: 2

Brand: Samsung Pages: 2

Brand: Samsung Pages: 2

Brand: Samsung Pages: 5

Brand: Samsung Pages: 26

Brand: Samsung Pages: 2

Brand: Samsung Pages: 38

Brand: Samsung Pages: 32

Brand: Samsung Pages: 38

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands