manualshive.com logo in svg

Siemens MICROMASTER, Reference Manual

Share
Download
Siemens MICROMASTER Reference Manual Download Page 75

COMBIMASTER & MICROMASTER Integrated

REFERENCE MANUAL

© 

Siemens plc. 1999

 |   G85139-H1731-U300-D2

74

Class 3:  Filtered -  for residential, commercial and light industry (Class B)

This level of performance will allow the manufacturer / assembler to self-certify compliance of their
apparatus with the EMC directive for the residential, commercial and light industrial environment as
regards the EMC performance characteristics of the power drive system. Performance limits are as
specified in the generic emission and immunity standards EN 50081-1 and EN 50082-1.

EMC Phenomenon

Standard

Level

Emissions: (CM)

Radiated Emissions

EN 55022

Level B1

Conducted Emissions

EN 55022

Level B1

Immunity: (CM & MMI)

Electrostatic Discharge

EN 61000-4-2

8 kV air discharge

Burst Interference

EN 61000-4-4

1 kV power cables, 0.5
kV control

The COMBIMASTER is intended 

exclusively for professional applications

.

Therefore, it does not fall within the scope of the harmonics emissions specification
EN 61000-3-2.

9.4 Environmental Aspects

Transport and Storage

Protect the COMBIMASTER/MMI against
physical shocks and vibration during
transport and storage. The unit must also
be protected against water (rainfall) and
excessive temperatures 

(see section 6).

The packaging is re-usable. Retain the
packaging or return it to the manufacturer
for future use.

Dismantling and Disposal

The component parts can be recycled,
disposed of in accordance with local
requirements or returned to the
manufacturer.

Documentation

This handbook is printed on chlorine-free
paper which has been produced from
managed sustainable forests. No solvents
have been used in the printing or binding
process.

Summary of Contents for MICROMASTER















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands