Siemens MICROMASTER Reference Manual Download Page 56

Page: 56 / 78

COMBIMASTER & MICROMASTER Integrated
REFERENCE MANUAL

Siemens plc. 1999

| G85139-H1731-U300-D2

COMBIMASTER - Case Size A - Deep Cover

Deep Cover – used for Electromechanical Brake Control Unit & Class B Filter (400V only)

(for Dimension TH for Case Size A , please refer to table on Page 53)

TH+22

COMBIMASTER - Case Size B – Deep Covers

Deeper Covers:
i)

Resistor Brake (incl. Heatsink)

ii) Mechanical

Brake

(for Dimension TH for Case Size B , please refer to table on Page 54)

For detailed Motor Dimension drawings, please refer to Siemens Catalogue M11 (ref.: E20002-K1711-
A101-A3-7600), Section 8 Dimension Drawings.

TH+30

TH+77

Dimensions in mm.
For detailed Motor Dimension drawings, please refer to Siemens Catalogue M11 (ref.: E20002-K1711-
A101-A3-7600), Section 8 Dimension Drawings.

Summary of Contents for MICROMASTER















































































Search results

Summary of Contents for MICROMASTER

Reviews:

Related manuals for MICROMASTER

Brands by name

Popular brands

Siemens MICROMASTER, Reference Manual

Search results

Summary of Contents for MICROMASTER

Reviews:

Related manuals for MICROMASTER

Brands by name

Popular brands