Rosemount 3107 Reference Manual Download Page 93 | Manualshive

Page: 93 / 148

background image

83

Reference Manual

00809-0200-4840, Rev BA

Section 5: Service and Troubleshooting

December 2014

Section 5: Service and Troubleshooting

5.5

Monitoring and diagnostic parameters

Note



For menu structures, see

Appendix C: Rosemount 3490 Series Universal Control Unit

or

Appendix D: Field Communicator

as appropriate for your HART Master Device.

Rosemount 3490 Series Control Unit

The 'D' prefixed parameters (e.g. D900) monitor the transmitter operation.
For convenience, the parameter identification numbers (D***) are used in parameter headings
and descriptions in this section.

A full menu map showing how to access transmitter parameters using the control unit’s menu
system is in

Appendix C: Rosemount 3490 Series Universal Control Unit

.

Note



The Rosemount 3490 Control Unit software must be version 3.40 or later.

Field Communicator and AMS

For convenience, Field Communicator fast key sequences are labeled
“Fast Keys” for each software function below the appropriate headings.

Example software function

Connect the Field Communicator leads to the transmitter, and turn on the Field Communicator
by pressing the ON/OFF key. The Field Communicator will search for a HART-compatible device
and indicate when the connection is made. If the Field Communicator fails to connect, it
indicates that no device was found. If this occurs, check the lead connections and re-try.

A full menu map showing how to access transmitter parameters using the Field Communicator
is in

Appendix D: Field Communicator

Fast Keys

1, 2, 3, etc.

«
...
91
92
93
94
95
...
»

Summary of Contents for 3107





















































































































































Reviews:

No comments

Related manuals for 3107

Brand: Hallicrafters Pages: 43

Brand: Vector Pages: 5

Brand: Ranger Pages: 18

Brand: Omron Pages: 2

Brand: Mhouse Pages: 2

FMx5001M Series

Brand: Jung Pages: 10

Brand: halstrup-walcher Pages: 32

Brand: Yaesu Pages: 41

Brand: Vectronic Aerospace Pages: 10

Brand: M-system Pages: 3

EXTA LIFE RNP-21

Brand: Zamel Pages: 2

Brand: IMG STAGE LINE Pages: 22

Brand: Allen-Bradley Pages: 4

Brand: Dwyer Instruments Pages: 4

Brand: Vanderbilt Pages: 8

Brand: Midland Pages: 3

Brand: Midland Pages: 24

Brand: Midland Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands