Rosemount 3107 Reference Manual Download Page 113

Page: 113 / 148

103

Reference Manual

00809-0200-4840, Rev BA

Section 5: Service and Troubleshooting

December 2014

Section 5: Service and Troubleshooting

5.5.20

Manufacturer (D960)

This is the manufacturer name.

Field Communicator or AMS

To view the manufacturer name:

From the

Home

screen, select 2: Configure.

Select 2: Manual Setup.

Select 4: HART/Identity.

Select 1: Identity.

Select 4: Manufacturer D960.

When finished, press EXIT to exit to the previous menu.

Rosemount 3490 Series Control Unit

To view the manufacturer name:

From the

Main Menu

screen, select SETUP.

Select the transmitter (e.g. “Tx1: 3107”).

Select SYSTEM.

Select FIXED.

Select HART.

Select Manufacturer.

When finished, select “

Quit

” to exit to the previous menu.

Fast Keys

2, 2, 4, 1, 4

Manufacturer D960
Rosemount

EXIT

HELP

(Field Communicator Screen)

Manufacturer D960
Rosemount

(Rosemount 3491 Screen)

Summary of Contents for 3107





















































































































































Search results

Summary of Contents for 3107

Reviews:

Related manuals for 3107

Brands by name

Popular brands

Rosemount 3107, Reference Manual

Search results

Summary of Contents for 3107

Reviews:

Related manuals for 3107

Brands by name

Popular brands