Rosemount 3107 Reference Manual Download Page 137

Page: 137 / 148

Reference Manual

00809-0200-4840, Rev BA

Appendix C: Rosemount 3490 Series Universal Control Unit

December 2014

127

Appendix C: Rosemount 3490 Series Universal Control Unit

Appendix C

Rosemount 3490 Series
Universal Control Unit

C.1

Menus and parameters

The Rosemount 3107 and Rosemount 3108 can be used with the Rosemount 3490 Series
Control Unit (

Table C-1 on page C-128

). This control unit supplies the 24 Vdc loop-power to the

transmitter, and provides control functionality using the 4–20 mA and HART signals from the
transmitter.

The control unit has HART communications capability, and access to all of the parameters of the
transmitter as shown in the following pages.

Note



The Rosemount 3490 Series manual (Document No. 00809-0100-4841) provides
detailed instructions on the use and features of the control unit.

Summary of Contents for 3107





















































































































































Search results

Summary of Contents for 3107

Reviews:

Related manuals for 3107

Brands by name

Popular brands

Rosemount 3107, Reference Manual

Search results

Summary of Contents for 3107

Reviews:

Related manuals for 3107

Brands by name

Popular brands