Rosemount 3107 Reference Manual Download Page 117

Page: 117 / 148

107

Reference Manual

00809-0200-4840, Rev BA

Section 5: Service and Troubleshooting

December 2014

Section 5: Service and Troubleshooting

5.5.24

Preambles (D964)

This is read by a HART Master Device e.g. a Rosemount 3490 Series Control Unit to determine
how many preamble bytes are to be sent with each HART protocol message.

Field Communicator or AMS

To view the number of preamble bytes:

From the

Home

screen, select 2: Configure.

Select 2: Manual Setup.

Select 4: HART/Identity.

Select 2: Communication.

Select 2: Preambles D964.

When finished, press EXIT to exit to the previous menu.

Rosemount 3490 Series Control Unit

To view the number of preamble bytes:

From the

Main Menu

screen, select SETUP.

Select the transmitter (e.g. “Tx1: 3107”).

Select SYSTEM.

Select FIXED.

Select HART.

Select Num Req Preams.

When finished, select “Quit” to exit to the previous menu.

Fast Keys

2, 2, 4, 2, 2

Preambles D964
5

EXIT

HELP

(Field Communicator Screen)

Num Req Preams D964
5

(Rosemount 3491 Screen)

Summary of Contents for 3107





















































































































































Search results

Summary of Contents for 3107

Reviews:

Related manuals for 3107

Brands by name

Popular brands

Rosemount 3107, Reference Manual

Search results

Summary of Contents for 3107

Reviews:

Related manuals for 3107

Brands by name

Popular brands