Rosemount 3107 Reference Manual Download Page 115

Page: 115 / 148

105

Reference Manual

00809-0200-4840, Rev BA

Section 5: Service and Troubleshooting

December 2014

Section 5: Service and Troubleshooting

5.5.22

HART revision (D962)

This is the major revision number of the standard used for the HART communications protocol.

Field Communicator or AMS

To view the HART revision number:

From the

Home

screen, select 1: Overview.

Select 3: Shortcuts.

Select 1: Device Information

twice

Select 1: Identification.

Select 4: HART Revision D962.

When finished, press EXIT to exit to the previous menu.

Rosemount 3490 Series Control Unit

To view the HART revision number:

From the

Main Menu

screen, select SETUP.

Select the transmitter (e.g. “Tx1: 3107”).

Select SYSTEM.

Select FIXED.

Select HART.

Select HART Rev.

When finished, select “Quit” to exit to the previous menu.

Fast Keys

1, 3, 1, 1, 1, 4

HART Revision D962
5

EXIT

HELP

(Field Communicator Screen)

HART Rev

D962

(Rosemount 3491 Screen)

Summary of Contents for 3107





















































































































































Search results

Summary of Contents for 3107

Reviews:

Related manuals for 3107

Brands by name

Popular brands

Rosemount 3107, Reference Manual

Search results

Summary of Contents for 3107

Reviews:

Related manuals for 3107

Brands by name

Popular brands