Rosemount 3107 Reference Manual Download Page 81

Page: 81 / 148

Reference Manual

00809-0200-4840, Rev BA

Section 4: Configuration

December 2014

Section 4: Configuration

4.3.31

Target pulses (P044)

Target Pulses

(

P044

) is the number of ultrasonic pulses in each burst sent from the transmitter

every second.

The factory default “

Automatic

” setting allows the transmitter to decide the number of pulses.

Alternatively, select a number in the range 4 to 32.

Note



See

Pulses in Use

(

page 98

) for the actual number of pulses used.

Field Communicator or AMS

To view or change the number of pulses in a burst:

From the

Home

screen, select

2: Configure

Select

2: Manual Setup

Select

7: Advanced Processing

Select

5: Set Target Pulses

Select

1: Target Pulses P044

Select a new setting, and then select “

ENTER

” to save it.

Press “

SEND

” to update the transmitter.

Rosemount 3490 Series Control Unit

To view or change the number of pulses in a burst:

From the

Main Menu

screen, select

SETUP

Select the transmitter (e.g. “

Tx1: 3107

”).

Select

ENGINEERING

Select

ADVANCED

Select

Target Pulses

Follow the on-screen instructions to edit and save the new setting.
(Press the

Enter

(

) key if prompted to change the mode to “off-line”).

Select “

Quit

” to exit to the previous menu.

Fast Keys

2, 2, 7, 5, 1

Target Pulses P044
AUTOMATIC

27
28
29
30
31
32
AUTOMATIC

AUTOMATIC

ENTER

ESC

(Field Communicator Screen)

Target Pulses P043

Automatic

Esc=Quit =Edit

(Rosemount 3491 Screen)

Summary of Contents for 3107





















































































































































Search results

Summary of Contents for 3107

Reviews:

Related manuals for 3107

Brands by name

Popular brands

Rosemount 3107, Reference Manual

Search results

Summary of Contents for 3107

Reviews:

Related manuals for 3107

Brands by name

Popular brands