Rosemount 3107 Reference Manual Download Page 29 | Manualshive

Page: 29 / 148

background image

Reference Manual

00809-0200-4840, Rev BA

Section 4: Configuration

December 2014

19

Section 4: Configuration

Section 4

Configuration

Overview   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 19
Command parameters   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 20
Configuration parameters   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  page 31

4.1

Overview

The Rosemount 3107 and Rosemount 3108 support HART communications, which may be used
to program or interrogate the transmitters from any point on the two-wire loop.

This section contains information on configuring the transmitters using a
Field Communicator, PC with AMS, or Rosemount 3490 Series Control Unit.

Rosemount 3490 Series control unit

The product manual 00809-0100-4841 provides detailed instructions on installation and
operation of the control unit.

A full menu map showing how to access transmitter parameters using the control unit’s menu
system is in Appendix

Appendix C: Rosemount 3490 Series Universal Control Unit

.

For convenience, the parameter identification numbers (P*** and D***) are used in parameter
headings and descriptions in this configuration section.

When using the control unit, use the

Enter

(

) key to start editing a configuration parameter

and then use the arrow keys to change the setting. Changes are confirmed by pressing the

Enter

key, or abandoned by pressing the

Esc

key. Commands e.g.

Set As Empty

are run using the

Enter

(

) key.

Note



The Rosemount 3490 Control Unit software must be version 3.40 or later.

Field Communicator and AMS

For convenience, Field Communicator fast key sequences are labeled
“Fast Keys” for each software function below the appropriate headings.

Example software function

When using a Field Communicator, some configuration changes are sent to the transmitter by
pressing “SEND”. AMS configuration changes are implemented when the “Apply” button is
clicked.

Connect the Field Communicator leads to the transmitter, and turn on the Field Communicator
by pressing the ON/OFF key. The Field Communicator will search for a HART-compatible device

Fast Keys

1, 2, 3, etc.

«
...
27
28
29
30
31
...
»

Summary of Contents for 3107





















































































































































Reviews:

No comments

Related manuals for 3107

Brand: Caliber Pages: 8

Brand: E+E Elektronik Pages: 33

Brand: Tachosys Pages: 17

Brand: Cable AML Pages: 26

Brand: Vectronic Aerospace Pages: 10

Brand: Gemini Pages: 2

Brand: AirTest Pages: 2

Brand: Erreka Pages: 2

Brand: Dahua Technology Pages: 13

Brand: Larson Electronics Pages: 2

Brand: Cobra Pages: 11

Brand: Cobra Pages: 42

Brand: MYE Pages: 5

Brand: Galaxy Pages: 9

Brand: Midland Pages: 23

Brand: Sony Pages: 2

Brand: Sony Pages: 4

Brand: Sony Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands