Rosemount 3107 Reference Manual Download Page 108

Page: 108 / 148

Reference Manual

00809-0200-4840, Rev BA

Section 5: Service and Troubleshooting

December 2014

Section 5: Service and Troubleshooting

5.5.15

Pulses in use (D918)

This is the actual number of pulses transmitted in the previous burst of pulses.

Note



The factory default setting is to automatically decide the number of pulses in a burst for
optimum performance (see Target Pulses on

page 71

)

Field Communicator or AMS

To view the number of pulses being used in a burst:

From the

Home

screen, select 3: Service Tools.

Select 1: Alerts.

Select 2: Diagnostic Data.

Select 3: Operation.

Select 3: Pulses In Use D918.

When finished, press EXIT to exit to the previous menu.

Note



This is also available at the Fast Key sequence 2, 2, 7, 5, 2
(see

Appendix D: Field Communicator

for a full menu map).

Rosemount 3490 Series Control Unit

To view the number of pulses being used in a burst:

From the

Main Menu

screen, select MONITOR.

Select the transmitter (e.g. “

Tx1: 3107

”).

Select DIAGNOSTICS.

Select OPERATION.

Select Pulses In Use.

When finished, select “

Quit

” to exit to the previous menu.

Fast Keys

3, 1, 2, 3, 3

Pulses in Use D918
10

EXIT

HELP

(Field Communicator Screen)

Pulses in Use D918

(Rosemount 3491 Screen Shown)

Summary of Contents for 3107





















































































































































Search results

Summary of Contents for 3107

Reviews:

Related manuals for 3107

Brands by name

Popular brands

Rosemount 3107, Reference Manual

Search results

Summary of Contents for 3107

Reviews:

Related manuals for 3107

Brands by name

Popular brands