Rosemount 3107 Reference Manual Download Page 96

Page: 96 / 148

Reference Manual

00809-0200-4840, Rev BA

Section 5: Service and Troubleshooting

December 2014

Section 5: Service and Troubleshooting

5.5.3

Distance / Tertiary Variable (TV) (D902)

This indicates the live distance-to-surface measured by the transmitter.
In HART terminology, this parameter is the Tertiary Variable (TV).

Note



Figure 4-1 on page 37

shows this parameter in a tank geometry illustration, and how

Distance Offset (

page 40

) affects this value.



Units are in meters, feet, or inches depending on base units (see

page 20

Field Communicator or AMS

To view the live distance-to-surface measurement:

From the

Home

screen, select 3: Service Tools.

Select 2: Variables.

Select 1: Variables.

Select 3: Distance (TV) D902.

When finished, press EXIT to exit to the previous menu.

Rosemount 3490 Series Control Unit

To view the live distance-to-surface measurement:

From the

Main Menu

screen, select MONITOR.

Select the transmitter (e.g. “

Tx1: 3107

”).

Select READINGS, and then select VARIABLES.

Select Distance (TV).

When finished, press the ESC key to exit to the previous menu.

Note



Units are in meters, feet, or inches depending on base units (see

page 20

Fast Keys

3, 2, 1, 3

Level (SV) D901
36.540 ft

EXIT

HELP

(Field Communicator Screen)

Distance (TV) D902

1.690ft

(Rosemount 3491 Screen)

Summary of Contents for 3107





















































































































































Search results

Summary of Contents for 3107

Reviews:

Related manuals for 3107

Brands by name

Popular brands

Rosemount 3107, Reference Manual

Search results

Summary of Contents for 3107

Reviews:

Related manuals for 3107

Brands by name

Popular brands