Rosemount 3107 Reference Manual Download Page 58

Page: 58 / 148

Reference Manual

00809-0200-4840, Rev BA

Section 4: Configuration

December 2014

Section 4: Configuration

4.3.13

Flow measurement

Table 4-1 on page 50

lists the

Tank Shape/Non-Linear Profile

(

P011

) options that select a

standard flow structure profile and the conversion (scale) factors used to calculate a flow
process value (PV).

Tank Shape/NLP (P011) = “Special Plot”

The “

Special Plot

” option is used for

irregular-shaped

flow profiles.

See

page 43

for a full description.

Tank Shape/NLP (P011) = “Flume/Weir-3/2”

This setting is applicable when flow rate measurements are needed from an open channel with a
flume or weir profile (see

Figure 4-6 on page 49

The rate of flow per second is calculated by:

Q = k x h

Pwr

Where ‘h’ is the live liquid level, ‘Q’ is flow rate per second, ‘Pwr’ is the power factor and ‘k’ is a
user-entered scale factor.

The transmitter automatically populates parameter

Power Factor / Profile Height

(

page 53

)

with a power factor from

Table 4-1

Flumes that deviate from the standard “3/2 power law”, e.g. round-bottomed flumes, must use
the “

Special Plot

” profile option that is based on flow versus height tabulations (see

page 43

Setting-up Procedure for “

Flume/Weir-3/2

”:

Use parameter

Tank Shape/NLP

(

P011

) to select “

Flume/Weir-3/2

”.

Enter the scale factor into the

PV Scale Factor

parameter (

page 52

Tank Shape/NLP (P011) = “V-Notch-5/2”

This setting is applicable when flow measurements are needed from an open channel with a
V-notch profile.

The rate of flow through a V-notch is calculated using:

Q = k x h

Pwr

Where ‘h’ is the live liquid level, ‘Q’ is flow rate per second, ‘Pwr’ is the power factor, and ‘k’ is a
user-entered scale factor.

The transmitter automatically populates parameter

Power Factor / Profile Height

(

page 53

)

with a power factor from

Table 4-1

Setting-up Procedure for “

V-Notch-5/2

”:

Edit parameter

Tank Shape/NLP

(

P011

) to select “

V-Notch-5/2

”.

Enter the scale factor into the

PV Scale Factor

parameter (

page 52

Summary of Contents for 3107





















































































































































Search results

Summary of Contents for 3107

Reviews:

Related manuals for 3107

Brands by name

Popular brands

Rosemount 3107, Reference Manual

Search results

Summary of Contents for 3107

Reviews:

Related manuals for 3107

Brands by name

Popular brands