Rosemount 3107 Reference Manual Download Page 99

Page: 99 / 148

Reference Manual

00809-0200-4840, Rev BA

Section 5: Service and Troubleshooting

December 2014

Section 5: Service and Troubleshooting

5.5.6

Current output (D906)

This indicates the actual output current in mA.

Note



When the Poll Address (

page 101

) is a non-zero number, the transmitter is in

multi-drop

mode

and the current output is fixed at 4 mA.

Field Communicator or AMS

To view the actual output current:

From the

Home

screen, select 3: Service Tools.

Select 2: Variables.

Select 2: Analog Output.

Select 1: Current Output.

When finished, press the Bksp key to exit to the previous menu.

Rosemount 3490 Series Control Unit

To view the actual output current:

From the

Main Menu

screen, select MONITOR.

Select the transmitter (e.g. “

Tx1: 3107

”).

Select READINGS, and then select CURRENT.

Select Current Output.

When finished, press the ESC key to exit to the previous menu.

Fast Keys

3, 2, 2, 1

Current Output - (mA)

Value: 19.047

HELP

(Field Communicator Screen)

Current Output D906

19.05mA

(Rosemount 3491 Screen)

Summary of Contents for 3107





















































































































































Search results

Summary of Contents for 3107

Reviews:

Related manuals for 3107

Brands by name

Popular brands

Rosemount 3107, Reference Manual

Search results

Summary of Contents for 3107

Reviews:

Related manuals for 3107

Brands by name

Popular brands