Riello 20187643, Installer And User Manual

Page: 17 / 116

17
ENGLISH
EN
Move inside the display until the
icon is highlighted. The error message will be displayed.
The faults description screen is automatically displayed once the display illumination time
has elapsed without any button being pressed.
Reset function
To restore boiler operation, press “ ENTER ” from the error message screen. At this point,
if the correct operating conditions have been restored, the boiler will restart automatically.
There are a maximum of 3 consecutive attempts at a release by the REC10CH. In case of
all the attempts are exhausted the definitive fault E099 occurs on the display. The boiler will
need to be unlock by cutting off and reconnecting the electrical supply.
E020
RESET ATT. EXHAUSTED
LIMIT THERMOSTAT
b
If the reset attempts do not activate the boiler, contact the Technical Assistance
Centre.
For fault E041: if the pressure drops below the safety threshold of 0.3 bar the boiler displays
the fault code “E041 - WATER TRANSDUCER FILL THE SYSTEM” for a transitional time
of 30 seconds during which it is possible to open the external filling tap until the pressure is
between 1 and 1.5 bar.
E041
FILL THE SYSTEM
WATER TRANSDUCER
b
If the drop in pressure is very frequent, contact the Technical Assistance Centre.
For fault E060: the appearance of this error, on only heating models with water tank with
probe connected, prevents DHW operation.
For fault E091: the boiler has an auto-diagnostic system which, based on the total number
of hours in certain operating conditions, can signal the need to clean the primary exchanger
(alarm code E091). Once the cleaning operation has been completed, reset to zero the total
hour meter with special kit supplied as an accessory following procedure indicated below:
- select TECHNICAL EXHAUST PROBE RESET CONFIRM or BACK.
CONFIRM OR DELETE SELECTION
CONFIRM CANCEL
THE PARAMETER WILL BE
CHANGED
RANGE RATED
CALIBRATION
WEATHER COMPENSATION
COMBUSTION ANALYSIS
EXHAUST PROBE RESET
INSTALLER
TECHNICAL
Note: The meter resetting procedure should be carried out after each in-depth cleaning of
the primary exchanger or if this latter is replaced.
The total hours can be verified in the following way: INFO menu FLUE GAS PROBE
press “ ENTER ” to display the value of the flue gases probe meter
30
°C
.3
MENU STATE
SET INFO
HOT WATER TEMPERATURE
FRI
1.3
bar
18/05/2013 12:17
PLANT
Boiler faults list
ERROR CODE ERROR MESSAGE DESCRIPTION OF TYPE OF ALARM
E010 flame lockout/ACF electronic fault definitive
E011 extraneous flame transitional
E020 limit thermostat definitive
E030 fan fault definitive
E040 water transducer – fill the system definitive
E041 water transducer – fill the system transitional
E042 water pressure transducer fault definitive
E060 water tank probe fault transitional
E070
flow sensor faulty
flow sensor overtemperature
flow/return sensor differential alarm
transitional
definitive
definitive
E077 main zone water thermostat transitional
E080
return line probe fault
return line probe overtemperature
outlet/return line probe differential alarm
transitional
definitive
definitive
E090
flue gas probe faulty
flue gas probe overtemperature
transitional
definitive
E091 clean primary heat exchanger transitional
E099 reset attempts exhausted, boiler blocked definitive, not resettable
-- water pressure low - check system transitional
-- water pressure high - check system transitional
-- boiler board communication lost transitional
-- BUS 485 communication lost transitional
List of combustion faults
ERROR CODE ERROR MESSAGE DESCRIPTION OF TYPE OF ALARM
E021 ACC monitor error
These are temporary alarms that if they occur several times in an hour they become definitive; the alarm E097 is displayed and is followed by
post-purging for 45 seconds at the fan's maximum speed.
It is always possible to release the alarm before the end of the post-purging.
E022 ACC monitor error
E023 ACC monitor error
E024 ACC monitor error
E067 ACC monitor error
E088 ACC monitor error
E097 ACC monitor error
E085 incomplete combustion
These are temporary alarms that if they occur several times in an hour they become definitive; the last error to occur is displayed and is
followed by a post-purging of 2 minutes at the fan's maximum speed. It is not possible to release the alarm before the end of the post-purging
unless the boiler's power supply is switched off.
E094 incomplete combustion
E095 incomplete combustion
E058 mains voltage fault
These are temporary faults that restrict the ignition cycle.
E065 current modulation alarm
E086 flue gases obstruction alarm Temporary fault signalled during Pre-Purging. Post-Purging is maintained for 5 min at maximum fan speed.