Renesas RX Series User Manual Download Page 318 | Manualshive

Page: 318 / 1823

background image

R01UH0823EJ0100 Rev.1.00

Page 318 of 1823

Jul 31, 2019

RX23W Group

17. Memory-Protection Unit (MPU)

17.

Memory-Protection Unit (MPU)

17.1

Overview

The RXv2 CPU incorporates a memory-protection unit that checks the addresses of CPU access to the overall address
space (0000 0000h to FFFF FFFFh).
Access-control information can be set for up to eight regions, and permission for access to each region is in accord with
this information. The default response to the detection of access to a region where permission has not been set is the
generation of a memory-protection error.
The supported access-control information for the individual regions consists of permission to read, permission to write,
and permission to execute. This access-control information is effective when the processor mode of the CPU is user
mode. Memory protection is not applied when the CPU is in supervisor mode.

lists the specifications of the memory-protection unit, and

shows a block diagram of the

memory-protection unit.

Table 17.1

Specifications of Memory Protection

Specifictaions

Description

Region to be covered by memory protection
and processor mode

0000 0000h to FFFF FFFFh (in user mode)
No memory protection in supervisor mode

Number of regions

8

Page size (smallest unit of protection)

16 bytes

Specifying addresses of individual regions

Setting the page numbers where regions start and end

Setting to make memory protection effective
or ineffective in individual regions

A V (valid) bit in each region-n end page number register (REPAGEn) makes the
settings effective or ineffective for the corresponding region (n = 0 to 7).

Access-control information settings for
individual regions

Instruction execution: Permission to execute
Operand access: Permission to read, permission to write

Start of memory-protection operations

After the memory-protection unit has been enabled, access monitoring starting up with
the transition to user mode.

Memory-protection error processing

Generation of access exceptions

Addresses where memory-protection errors
are generated

Address in instruction execution: The PC value is preserved on the stack.
Address in operand access: The address is stored in the data memory-protection error
address register (MPDEA).

Determining the reasons for memory-
protection errors

The memory-protection error status register (MPESTS) holds indicators of the reason.

Background region setting

Access-control information can be set for the background region (the whole address
space).

Processing where regions overlap

The access-control information for access to an overlap between regions is the logical
OR of the attributes for the given regions, and permission is given priority.

«
...
316
317
318
319
320
...
»

Summary of Contents for RX Series
































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RX Series

Brand: LORD Pages: 9

Brand: Edge-Core Pages: 7

Brand: Intel Pages: 108

Brand: Black Box Pages: 9

Brand: Usr Pages: 2

Brand: Black Box Pages: 37

Proventia A1204

Brand: Internet Security Systems Pages: 42

AIE900-XNX Series

Brand: AXIOMTEK Pages: 53

LBON320AC Series

Brand: Lindsay Broadband Pages: 4

Brand: QNAP Pages: 54

Brand: Cisco MERAKI Pages: 4

Brand: Paradyne Pages: 6

cPCIS-1100 Series

Brand: ADLINK Technology Pages: 48

Brand: ADTRAN Pages: 2

Brand: Aim Pages: 35

Brand: Rane Pages: 6

Fibe-Air IP-10G

Brand: Ceragon Pages: 71

Brand: Enterasys Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands