manualshive.com logo in svg

Renesas RX Series, User Manual

Introducing the artisan RX Series Instruction Manual, an essential resource for getting the most out of your artisan RX product. Easily download this comprehensive manual for free from manualshive.com, providing you with detailed instructions and guidance for seamless usage and optimum performance.

Share
Download
background image

R01UH0823EJ0100 Rev.1.00

Page 809 of 1823

Jul 31, 2019

RX23W Group

29. Low-Power Timer (LPT)

LPCMRE0 Bit (Compare Match 0 Enable)

This bit enables or disables low-power timer compare match 0.
When the low-power timer is put into operation and the MCU makes a transition to software standby mode while this bit 
and the LPWUCR.LPWKUPEN bit are set to 1 (wakeup from software standby mode using low-power timer is enabled), 
the MCU returns from software standby mode to normal operating mode through the event link controller (ELC) when 
the value of the low-power timer counter and the setting of the LPCMR0 register matches.
Modify this bit while the LPTCR3.LPCNTEN bit is 0 (low-power timer counter stops).
Do not write to this bit while the LPTCR3.LPCNTEN bit is 1 (low-power timer counter operates).
Settings for the interrupt and ELC are necessary to use a compare match 0 as a trigger source to return from software 
standby mode.
Refer to 

section 20, Event Link Controller (ELC)

 for details on the ELC settings, and refer to 

section 15, Interrupt 

Controller (ICUb)

 for details on the interrupt settings.

An interrupt request at compare match 0 is generated only in software standby mode. It is not generated in normal 
operating mode, sleep mode, and deep sleep mode.

Summary of Contents for RX Series
































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RX Series

TC Electronic ATAC Service Manual preview
ATAC
Brand: TC Electronic Pages: 55
GAMDIAS Aura GC2 Quick Installation Manual preview
Aura GC2
Brand: GAMDIAS Pages: 15
IDT TSI384 User Manual preview
TSI384
Brand: IDT Pages: 281
DMX4ALL DMX-Universal-Demux User Manual preview
DMX-Universal-Demux
Brand: DMX4ALL Pages: 17
Rockwell Automation 41LR4060 Instruction Manual preview
41LR4060
Brand: Rockwell Automation Pages: 108
Analog Devices ADAU1961 Manual preview
ADAU1961
Brand: Analog Devices Pages: 76
Internet Security Systems Proventia A1204 User Manual preview
Proventia A1204
Brand: Internet Security Systems Pages: 42
Tektronix CTS 850 User Manual preview
CTS 850
Brand: Tektronix Pages: 178
Zhone IMACS Network Device Product Manual preview
IMACS Network Device
Brand: Zhone Pages: 114
Renesas RL78/G11 User Manual preview
RL78/G11
Brand: Renesas Pages: 2
Segger J-Link-OB-STM32F072-128KB User Manual preview
J-Link-OB-STM32F072-128KB
Brand: Segger Pages: 18
Seagate CHEETAH ST34501FC Product Manual preview
CHEETAH ST34501FC
Brand: Seagate Pages: 68
Inspired Energy ATA004N Operating Instructions preview
ATA004N
Brand: Inspired Energy Pages: 5
McIntosh MX160 Owner'S Manual preview
MX160
Brand: McIntosh Pages: 44
Riverbed SteelCentral NetExpress 470 Upgrade And Maintenance Manual preview
SteelCentral NetExpress 470
Brand: Riverbed Pages: 140
Kontron ADA-SDVO-PEG16 User Manual preview
ADA-SDVO-PEG16
Brand: Kontron Pages: 14
Rajant BreadCrumb ES1 User Manual preview
BreadCrumb ES1
Brand: Rajant Pages: 93
Harman Lexicon MPX 200 User Manual preview
Lexicon MPX 200
Brand: Harman Pages: 77

Brands by name

Popular brands

Load more brands