manualshive.com logo in svg

Renesas RX Series, User Manual

Introducing the artisan RX Series Instruction Manual, an essential resource for getting the most out of your artisan RX product. Easily download this comprehensive manual for free from manualshive.com, providing you with detailed instructions and guidance for seamless usage and optimum performance.

Share
Download
background image

R01UH0823EJ0100 Rev.1.00

Page 492 of 1823

Jul 31, 2019

RX23W Group

23. Multi-Function Timer Pulse Unit 2 (MTU2a)

TGIEA and TGIEB Bits (TGR Interrupt Enable A and B)

Each bit enables or disables interrupt requests (TGIm) (m = A, B).

TGIEC and TGIED Bits (TGR Interrupt Enable C and D)

Each bit enables or disables interrupt requests (TGIm) in MTU0, MTU3, and MTU4 (m = C, D).
In MTU1 and MTU2, these bits are reserved. They are read as 0. The write value should be 0.

TCIEV Bit (Overflow Interrupt Enable)

This bit enables or disables interrupt requests (TCIV).

TCIEU Bit (Underflow Interrupt Enable)

This bit enables or disables interrupt requests (TCIU) in MTU1 and MTU2.
In MTU0, MTU3, and MTU4, this bit is reserved. It is read as 0. The write value should be 0.

TTGE2 Bit (A/D Converter Start Request Enable 2)

This bit enables or disables generation of A/D converter start requests by MTU4.TCNT underflow (trough) in 
complementary PWM mode.
In MTU0 to MTU3, this bit is reserved. It is read as 0. The write value should be 0.

TTGE Bit (A/D Converter Start Request Enable)

This bit enables or disables generation of A/D converter start requests by the TGRA input capture/compare match.

MTU0.TIER2

TGIEE and TGIEF Bits (TGR Interrupt Enable E and F)

Each bit enables or disables interrupt requests by compare match between the MTU0.TCNT counter and the 
MTU0.TGRm register (m = E, F).

Address(es): MTU0.TIER2 000D 0B24h

b7

b6

b5

b4

b3

b2

b1

b0

—

—

—

—

—

—

TGIEF TGIEE

Value after reset:

0

0

0

0

0

0

0

0

Bit

Symbol

Bit Name

Description

R/W

b0

TGIEE

TGR Interrupt Enable E

0: Interrupt requests (TGIE) disabled
1: Interrupt requests (TGIE) enabled

R/W

b1

TGIEF

TGR Interrupt Enable F

0: Interrupt requests (TGIF) disabled
1: Interrupt requests (TGIF) enabled

R/W

b7 to b2

—

Reserved

These bits are read as 0. The write value should be 0.

R/W

Summary of Contents for RX Series
































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RX Series

Javad TRIUMPH-3NR User Manual preview
TRIUMPH-3NR
Brand: Javad Pages: 35
Omega Engineering OME-A8111 Hardware Manual preview
OME-A8111
Brand: Omega Engineering Pages: 34
Supero Supero SAS-826A User Manual preview
Supero SAS-826A
Brand: Supero Pages: 16
N.A.T. NAT-MCH Technical Reference Manual preview
NAT-MCH
Brand: N.A.T. Pages: 32
B&B Electronics Parallel Printer Card PIOC User Manual preview
Parallel Printer Card PIOC
Brand: B&B Electronics Pages: 16
Zoom 4412A User Manual preview
4412A
Brand: Zoom Pages: 48
RAIDAGE DAGE312UTL-NAS User Manual preview
DAGE312UTL-NAS
Brand: RAIDAGE Pages: 60
C&T Solution VCO-6131E-4M2 User Manual preview
VCO-6131E-4M2
Brand: C&T Solution Pages: 129
G&D DL-DVI-Vision-IP Series Installation And Operation Manual preview
DL-DVI-Vision-IP Series
Brand: G&D Pages: 228
Cypress Semiconductor CY62136EV30 MoBL Specification Sheet preview
CY62136EV30 MoBL
Brand: Cypress Semiconductor Pages: 12
Lindy 32116 User Manual preview
32116
Brand: Lindy Pages: 12
ExtraHop EDA 4200 Install preview
EDA 4200
Brand: ExtraHop Pages: 2
Digital Audio Corporation PCAP II User Manual preview
PCAP II
Brand: Digital Audio Corporation Pages: 164
Dave Embedded Systems diDo Hardware Manual preview
diDo
Brand: Dave Embedded Systems Pages: 79
3Com 3CRWE737A - 11Mbps Airconnect Wireless Lan PC Card... Datasheet preview
3CRWE737A - 11Mbps Airconnect Wireless Lan PC Card...
Brand: 3Com Pages: 6
ICP DAS USA ZT-2005-C8 User Manual preview
ZT-2005-C8
Brand: ICP DAS USA Pages: 60
Olivella Modular Signos User Manual preview
Signos
Brand: Olivella Modular Pages: 19
Freescale Semiconductor i.MX 6SoloLite Linux Reference Manual preview
i.MX 6SoloLite Linux
Brand: Freescale Semiconductor Pages: 199

Brands by name

Popular brands

Load more brands