manualshive.com logo in svg

Renesas RX Series, User Manual

Introducing the artisan RX Series Instruction Manual, an essential resource for getting the most out of your artisan RX product. Easily download this comprehensive manual for free from manualshive.com, providing you with detailed instructions and guidance for seamless usage and optimum performance.

Share
Download
background image

R01UH0823EJ0100 Rev.1.00

Page 640 of 1823

Jul 31, 2019

RX23W Group

24. Port Output Enable 2 (POE2a)

24.

Port Output Enable 2 (POE2a)

The port output enable 2 (POE) module can be used to place the states of the pins for complementary PWM output by the 
MTU (MTIOC3B, MTIOC3D, MTIOC4A, MTIOC4B, MTIOC4C, and MTIOC4D), and the states of pins for MTU0 
(MTIOC0A, MTIOC0B, and MTIOC0C) in the high-impedance in response to changes in the input levels on the POE0#, 
POE1#, POE3# and POE8# pins, in the output levels on pins for complementary PWM output by the MTU, oscillation 
stop detection by the clock generation circuit, and changes to register settings (SPOER) or event signal input from the 
event link controller (ELC).
It can also generate simultaneous interrupt requests.
In this section, “PCLK” is used to refer to PCLKB.

24.1

Overview

Table 24.1

 lists the specifications of the POE, and 

Figure 24.1

 shows a block diagram of the POE.

The POE has input-level detection circuits, output-level comparison circuits, an input for the oscillation stop detection 
signal from the clock generation circuit, and a high-impedance request/interrupt request generating circuit as shown in 

Figure 24.1

.

Table 24.1

POE Specifications

Item

Description

High-impedance is controlled by 
the input level detection

Falling-edge detection or sampling of the low level 16 times at PCLK/8, PCLK/16, or PCLK/128 
clock cycles can be set for each of the POE0#, POE1#, POE3# and POE8# input pins.

Pins for complementary PWM output from the MTU can be placed in the high-impedance on 
detection of falling edges or sampling of the low level on the POE0# to POE3# pins. 

Pins for output from MTU0 can be placed in the high-impedance on detection of falling edges or 
sampling of the low level on the POE8# pin.

High-impedance is controlled by 
the output level comparison

Levels output on pins for complementary PWM output from the MTU are compared, and when 
simultaneous output of the active level continues for one or more clock cycles, the pins can be 
placed in the high-impedance. 

High-impedance is controlled by 
the oscillation stop detection

Pins for complementary PWM output from the MTU and output pins for MTU0 can be placed in 
the high-impedance when oscillation by the clock generation circuit stops.

High-impedance is controlled by 
software (registers)

Pins for complementary PWM output from the MTU and output pins for MTU0 can be placed in 
the high-impedance by modifying settings of POE registers.

High-impedance is controlled by 
the event signal

Pins for complementary PWM output from the MTU and output pins for MTU0 can be placed in 
the high-impedance in response to an event signal from the event link controller (ELC).

Interrupts

Interrupts can be generated in response to the results of POE0#, POE1#, POE3# and POE8# 
input-level detection and MTU complementary PWM output-level comparison.

Summary of Contents for RX Series
































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RX Series

D-Link DFE-690TXD Quick Install Manual preview
DFE-690TXD
Brand: D-Link Pages: 12
CAME Z Series Manual preview
Z Series
Brand: CAME Pages: 4
ICP DAS USA ET-7000 series Quick Start Manual preview
ET-7000 series
Brand: ICP DAS USA Pages: 14
ICP DAS USA I-2533 User Manual preview
I-2533
Brand: ICP DAS USA Pages: 25
ICP DAS USA ET-2200 Series Manual preview
ET-2200 Series
Brand: ICP DAS USA Pages: 15
ICP DAS USA PCIe-S112 Quick Start Manual preview
PCIe-S112
Brand: ICP DAS USA Pages: 8
Nvidia DGX A100 User Manual preview
DGX A100
Brand: Nvidia Pages: 115
Supersonic Franky Instruction Manual preview
Franky
Brand: Supersonic Pages: 46
ICOP Technology Vortex86SX VSX-6100 User Manual preview
Vortex86SX VSX-6100
Brand: ICOP Technology Pages: 50
Lattice Semiconductor sysCLOCK ECP5 Usage Manual preview
sysCLOCK ECP5
Brand: Lattice Semiconductor Pages: 43
Paradyne ACCULINK 3161 CSU Quick Reference Manual preview
ACCULINK 3161 CSU
Brand: Paradyne Pages: 19
Dataprobe iBoot Instruction Manual preview
iBoot
Brand: Dataprobe Pages: 16
SriHome NVS001B Quick Operation Manual preview
NVS001B
Brand: SriHome Pages: 12
National Instruments IMAQTM User Manual preview
IMAQTM
Brand: National Instruments Pages: 121
Digital Voice Systems VC-20-MR2 User Manual preview
VC-20-MR2
Brand: Digital Voice Systems Pages: 32
Oracle Acme Packet 3900 Hardware Installation And Maintenance Manual preview
Acme Packet 3900
Brand: Oracle Pages: 70
Z3 Technology DM8168-MOD-35 Manual preview
DM8168-MOD-35
Brand: Z3 Technology Pages: 22
Intel G6950 Documentation Update preview
G6950
Brand: Intel Pages: 51

Brands by name

Popular brands

Load more brands