manualshive.com logo in svg

Renesas RX Series, User Manual

Introducing the artisan RX Series Instruction Manual, an essential resource for getting the most out of your artisan RX product. Easily download this comprehensive manual for free from manualshive.com, providing you with detailed instructions and guidance for seamless usage and optimum performance.

Share
Download
background image

R01UH0823EJ0100 Rev.1.00

Page 1059 of 1823

Jul 31, 2019

RX23W Group

33. Serial Communications Interface (SCIg, SCIh)

Figure 33.44

 shows a sample flowchart for serial data reception.

Figure 33.44

Sample Smart Card Interface Reception Flowchart

All the processing steps are automatically performed using an RXI interrupt request to activate the DTC or DMAC.
In reception, setting the RIE bit to 1 allows an RXI interrupt request to be generated. The DTC or DMAC is activated by 
an RXI interrupt request if the RXI interrupt request is specified as a source of DTC or DMAC activation beforehand, 
allowing transfer of receive data.
If an error occurs during reception and either the ORER or PER flag in the SSR register is set to 1, a receive error 
interrupt (ERI) request is generated. Clear the error flag after the error occurrence. If an error occurs, the DTC or DMAC 
is not activated and receive data is skipped. Therefore, the number of bytes of receive data specified in the DTC or 
DMAC is transferred.
Even if a parity error occurs and the PER flag is set to 1 during reception, receive data is transferred to RDR, thus 
allowing the data to be read.
When a reception is forcibly terminated by setting the SCR.RE bit to 0 during operation, read the RDR register because 
the received data which has not yet been read may be left in RDR.

Note 1. For operations in block transfer mode, refer to section 33.3, Operation in Asynchronous Mode.

Initialization

Read data from RDR

Set bits RIE and RE 

in SCR to 0

Start data reception

Start

Error processing

No

No

No

Yes

Yes

SSR.ORER = 0 and 

SSR.PER = 0?

RXI interrupt

All data received?

Yes

Summary of Contents for RX Series
































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RX Series

TC Electronic M300 Service Manual preview
M300
Brand: TC Electronic Pages: 2
Parker H Series Installation & Service Instructions Manual preview
H Series
Brand: Parker Pages: 344
NEC Univerge SV9300 Migration Manual preview
Univerge SV9300
Brand: NEC Pages: 26
NEC NEAX 2400 Quick Reference Manual preview
NEAX 2400
Brand: NEC Pages: 20
NEC DS2000 IntraMail Instructions preview
DS2000 IntraMail
Brand: NEC Pages: 2
Aastra CNX Product Brief preview
CNX
Brand: Aastra Pages: 2
LaCie d2 Network 2 Quick Install Manual preview
d2 Network 2
Brand: LaCie Pages: 44
LaCie LaCie Ethernet Disk Datasheet preview
LaCie Ethernet Disk
Brand: LaCie Pages: 2
LaCie SATA II ExpressCard 34 Datasheet preview
SATA II ExpressCard 34
Brand: LaCie Pages: 2
LaCie 12big Rack Fibre 8 Quick Install Manual preview
12big Rack Fibre 8
Brand: LaCie Pages: 9
Ubiquiti NanoBeam M5 Setup preview
NanoBeam M5
Brand: Ubiquiti Pages: 3
AMD SB710 User Manual preview
SB710
Brand: AMD Pages: 20
Tandberg Data Storagelibrary T24 Manual preview
Storagelibrary T24
Brand: Tandberg Data Pages: 28
Internet Security Systems Proventia A1204 User Manual preview
Proventia A1204
Brand: Internet Security Systems Pages: 42
AXIOMTEK eBOX532-100-FL Series Quick Installation Manual preview
eBOX532-100-FL Series
Brand: AXIOMTEK Pages: 2
AOpen VA1000 Lite2 User Manual And Technical Manual preview
VA1000 Lite2
Brand: AOpen Pages: 18
iesy Open Standard Module RPX30 EVA-MI V1 Quick Start Manual preview
Open Standard Module RPX30 EVA-MI V1
Brand: iesy Pages: 9
Microchip Technology PD-9501-10GCO/AC User'S Installation Manual preview
PD-9501-10GCO/AC
Brand: Microchip Technology Pages: 41

Brands by name

Popular brands

Load more brands