manualshive.com logo in svg

RAM Ram Dodge 2010, Owner'S Manual


Share
Download
background image

The user interface consists of the following:

GAIN/ Brake Output Power Display

Shows the current GAIN setting.

This display may also be used to display diagnostic
information, if needed.

•

SC — Short Circuit to Ground

•

Sb — Short to Battery

•

CF — Controller Fault – If this message appears on the
display, see your authorized dealer.

When the vehicle brakes are applied, the display will no
longer show GAIN and will change to the output to the
trailer brakes.

Manual Brake Control Lever

Slide the manual brake control lever to the right to
activate power to the trailer’s electric brakes independent
of the tow vehicle’s brakes. If the manual brake control

lever is activated while the brake is also applied, the
greater of the two inputs determines the power sent to
the trailer brakes.

The trailer and the vehicle’s brake lamps will come on
when either vehicle braking or manual trailer brakes are
applied.

Trailer Brake Status Indicator Light

This light indicates the trailer electrical connection status.

If no electrical connection is detected after the ignition is
turned on, pressing the GAIN adjustment button or
sliding the manual brake control lever will display the
GAIN setting for 10 seconds and the “Trailer Brake Status
Indicator Light” will not be displayed.

If a fault is detected in the trailer wiring or the Integrated
Trailer Brake Module (ITBM), the “Trailer Brake Status
Indicator Light” will flash.

5

STARTING AND OPERATING

455

Summary of Contents for Ram Dodge 2010









































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Ram Dodge 2010

Daihatsu F300 Service Manual preview
F300
Brand: Daihatsu Pages: 1718
Wallbox Commander 2 Installation And User Manual preview
Commander 2
Brand: Wallbox Pages: 7
Napoli NPL-TV 7874 DIGITAL Instruction Manual preview
NPL-TV 7874 DIGITAL
Brand: Napoli Pages: 20
BrandMotion 1009-6503 Installation Instructions Manual preview
1009-6503
Brand: BrandMotion Pages: 8
Metra Electronics 95-8202 Installation Instructions Manual preview
95-8202
Brand: Metra Electronics Pages: 20
RAM 1500 2WD 2021 Owner'S Manual preview
1500 2WD 2021
Brand: RAM Pages: 496
Yakima K1249 Instructions Manual preview
K1249
Brand: Yakima Pages: 9
Magneti Marelli 350203061230 Installation Instruction preview
350203061230
Brand: Magneti Marelli Pages: 2
ULTIMATE SPEED UAWSO 2 B1 Operation And Safety Notes preview
UAWSO 2 B1
Brand: ULTIMATE SPEED Pages: 32
Chevrolet 1998 Tahoe Manual preview
1998 Tahoe
Brand: Chevrolet Pages: 441
ICON 91824E Installation Instructions preview
91824E
Brand: ICON Pages: 4
Mazda 0000-8L-G03A Installation Instructions preview
0000-8L-G03A
Brand: Mazda Pages: 3
GYS 029422 Manual preview
029422
Brand: GYS Pages: 32
Belkin TuneBase F8Z442 User Manual preview
TuneBase F8Z442
Brand: Belkin Pages: 162
Tactik Tube Doors Installation & Use Instructions preview
Tube Doors
Brand: Tactik Pages: 4
banks 61410 Owner'S Manual preview
61410
Brand: banks Pages: 76
APS iBoard IB-R159 Manual preview
iBoard IB-R159
Brand: APS Pages: 4
Metra Electronics 99-7804 Installation Instructions Manual preview
99-7804
Brand: Metra Electronics Pages: 10

Brands by name

Popular brands

Load more brands