background image

WARNING!

Never have any smoking materials lit in or near
the vehicle when the gas cap is removed or the
tank filled.

Never add fuel to the vehicle when the engine is
running.

A fire may result if gasoline is pumped into a
portable container that is inside of a vehicle. You
could be burned. Always place gas containers on
the ground while filling.

NOTE:

Tighten the gas cap until you hear a “clicking” sound.
This is an indication that the gas cap is tightened
properly. The MIL in the instrument cluster may turn
on if the gas cap is not secured properly. Make sure
that the gas cap is tightened each time the vehicle is
refueled.

When the fuel nozzle “clicks” or shuts off, the fuel
tank is full.

Loose Fuel Filler Cap Message

If the vehicle diagnostic system determines
that the fuel filler cap is loose, improperly
installed, or damaged, a loose gascap indicator
will display in the EVIC telltale display area.

Refer to “Electronic Vehicle Information Center (EVIC) in
“Understanding Your Instrument Panel” for further in-
formation. Tighten the fuel filler cap properly and press
the SELECT button to turn off the message. If the
problem continues, the message will appear the next time
the vehicle is started.

5

STARTING AND OPERATING

441

Summary of Contents for Ram Dodge 2010









































































































































































































































































































































































































































































































































































































































Reviews: