manualshive.com logo in svg

RAM Ram Dodge 2010, Owner'S Manual


Share
Download
background image

1 (First)

This range is for hard pulling at low speeds in mud, sand,
snow, or on steep grades. Begins and stays in low gear
with no upshift. Provides engine compression braking at
low speeds.

Overdrive Operation

The Overdrive automatic transmission contains an elec-
tronically controlled fourth gear (OVERDRIVE). The
transmission will automatically shift from third gear to
OVERDRIVE if the following conditions are present:

•

the shift lever is in DRIVE

•

the engine coolant has reached normal operating tem-
perature

•

vehicle speed is above approximately 30 mph
(48 km/h)

•

the TOW/HAUL switch has not been activated

•

the transmission has reached normal operating
temperature

NOTE:

If the vehicle is started in extremely cold tem-

peratures, the transmission may not shift into OVER-
DRIVE and will automatically select the most desirable
gear for operation at this temperature. Normal operation
will resume when the transmission fluid temperature has
risen to a suitable level.

If the transmission temperature gets extremely hot, the
transmission will automatically select the most desirable
gear for operation at this temperature. If the transmission
temperature becomes hot enough, the “Transmission
Temperature Warning Light” may illuminate and the
transmission may downshift out of OVERDRIVE until
the transmission cools down. After the transmission cools
down, the transmission will resume normal operation.

308

STARTING AND OPERATING

Summary of Contents for Ram Dodge 2010









































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Ram Dodge 2010

Yakima K343 Manual preview
K343
Brand: Yakima Pages: 11
Harmar Mobility AL001 Installation And Owner'S Manual preview
AL001
Brand: Harmar Mobility Pages: 10
Ignition 63-231 Quick Start preview
63-231
Brand: Ignition Pages: 1
SAF-HOLLAND FleetMaster Air FW8 Series Owner'S Manual preview
FleetMaster Air FW8 Series
Brand: SAF-HOLLAND Pages: 20
Yakima Prorack K436 Fitting Instructions Manual preview
Prorack K436
Brand: Yakima Pages: 13
E&G Classics 1409-0102-10 Installation Instructions preview
1409-0102-10
Brand: E&G Classics Pages: 3
RBO RBO4038 Product Manual preview
RBO4038
Brand: RBO Pages: 15
Lantronix FOX3 Series Hardware Manual preview
FOX3 Series
Brand: Lantronix Pages: 51
Ford Focus 2008 Quick Reference Manual preview
Focus 2008
Brand: Ford Pages: 2
Menabo ANTARES KIT+1 Assembly & Instruction Manual preview
ANTARES KIT+1
Brand: Menabo Pages: 8
Seat Arona 2018 Owner'S Manual preview
Arona 2018
Brand: Seat Pages: 372
Audi 2001 A3 Quick Reference Manual preview
2001 A3
Brand: Audi Pages: 4
Thule Brink 5324 Fitting Instructions Manual preview
Brink 5324
Brand: Thule Pages: 15
Magneti Marelli AC911 Installation Instruction preview
AC911
Brand: Magneti Marelli Pages: 3
Edelbrock 67312 Installation Instructions preview
67312
Brand: Edelbrock Pages: 2
BabySafe Beagle User Manual preview
Beagle
Brand: BabySafe Pages: 43
E-Lead EL-HA1 Manual preview
EL-HA1
Brand: E-Lead Pages: 11
Safe Fleet RVS-218629 Instruction Manual preview
RVS-218629
Brand: Safe Fleet Pages: 28

Brands by name

Popular brands

Load more brands